Bedienungsanleitung Felisatti RF30 (Seite 3 von 25) (Deutsch, Englisch, Französisch, Italienisch, Portugiesisch, Spanisch)

502508

Zoom out

Zoom in

Vorherige Seite

1/25

Nächste Seite

TECHNICAL DATA

Milling machine RF30/430

bsorbed powe

W 430

No load speed rpm 26000

 of milling cutter attachment

mm 6

Lengthwise travel mm 30

Cross slide shift mm 28

Machine weight (without accessories) kg 1.9

The instructions contained in this manual must be strictly

followed, it should be carefully read and kept close at

hand to use when carrying out maintenance on the

indicated parts.

If the machine is used carefully and normal maintenance

is carried out, it will work for a long time.

The functions and use of the tool you have bought shall

be only those described in this manual. Any other use

of the tool is strictly forbidden.

EQUIPMENT

- 1 hard metal milling cutter, 14 mm 

- 1 adjustable cross slide

- 1 fixed spanner, 17 mm

- Operating instructions

- Safety instructions

- Warranty

SAFETY INSTRUCTIONS

 See “Safety Instructions” enclosed manual, supplied

together with this instruction manual.

 WARNING! The dust produced when milling asbestos

and/or silica stone materials is dangerous to health.

Follow the insurance company’s safety instructions

regarding the responsibility of employees.

 For your personal safety, always connect the machine

to a mains supply by a differential and thermal cut-out

switch, in accordance with regulations on low-voltage

wiring sitemaps.

 Do not perforate the machine casing, as this would

destroy the protective insulation (use adhesive labels).

 Always unplug the machine before doing any work on it.

 Always stop the machine by switching it off, not by

unplugging it.

 WARNING! Before each use, inspect the plug and

lead. Should they need replacing, have this done by an

official service centre. Only plug the machine in when it

is switched off.

 Always keep the lead out of the machine’s working

area.

 Only plug the machine in when it is switched off.

 Do not allow the machine to get wet, nor should it be

used in wet environments.

 When using the machine, always wear safety goggles,

gloves and non-slip footwear, and it is advisable to

wear ear protection.

 Check for correct piece fixing before commencing any

operation.

 Only milling heads with acceptable revolutions that are

at least the same as the maximum off-load revolutions

of the machine should be used.

 The milling head shaft diameter should match the

inside diameter of the tool-holder (locking clip).

 It should be ensured that the milling head is firmly held

in place before the machine is operated.

 The clip-carrier shaft support lever must only be oper-

ated when the machine is stopped.

 The milling head should only be brought into contact

with the work-piece after it has been switched on.

 Hold the machine firmly in both hands and in a stable

position.

 The milling machine must never be used on metal

objects, such as nails and screws.

 Hand must be kept clear of the milling machine while it

is operating.

 The operator should remain alert and keep the milling

head apart from all objects during operation.

 The motor must be allowed to come to completely stop

before being put to one side between uses.

 The milling heads should be protected from impacts

and knocks.

 The milling heads should not be touched after use

because they could cause serious burns.

STARTING THE TOOL

Make sure the mains voltage is correct: it must be the

same as that on the specification label. Machines with

230-V can also be connected to a 220-V mains supply.

Pressing On/Off switch will turn the machine on and

releasing it will turn it off again. For continuous operation,

press ON/OFF switch and lock it in the operating position

using safety switch button. If ON/OFF switch is pressed

and released again, the machine will switch off.

ADJUSTMENT OF DEPTH (Fig. 3 and 4)

By loosening the screws (t) and overcoming the pres-

sure of the springs (k), the depth of cut can be adjusted

by letting the end of the cutter stick out the required

amount from the support plane of the base of square (e)

of the mobile cross slide. Tighten up screws (t). The

pointer of the ring (j) on the millimitre-graded rule (c) can

be used as a reference for the depth adjustment. The

working depth can be fixed by limiting it via screw (b)

and counternut (B). When the machine is not in use, it

is advisable to loosen the screws (t) and let the base

protrude as far as possible through the action of the

springs, in order to protect the milling cutter. When

working with the machine, retract the base to the pre-set

stop and tighten the screws (t).

ADJUSTMENT OF MOBILE SLIDE (Fig. 5)

Loosen screw (f) and adjust the cross travel of the

mobile slide (e) by means of the adjustment screw (n),

relocking screw (f) at the required setting. Use the inside

pointer (d) with regard to the millimetre-graded scale (p)

as a reference for the amount of shift.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Felisatti RF30 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info