Bedienungsanleitung Felisatti RF30 (Seite 4 von 25) (Deutsch, Englisch, Französisch, Italienisch, Portugiesisch, Spanisch)

502508

Zoom out

Zoom in

Vorherige Seite

1/25

Nächste Seite

FITTING THE HINGES

The hinges to be fitted are those of (Fig. 10). Use mill-

ing cutters of the same diameter as the hinge width.

Hold the hinge against the side of the door and mark the

end points of the hinge recess (Fig. 6).

Once the milling cutter has been graded both depth-wise

and laterally the actual cutting operation may ben started

by taking the cutter in frontally and supporting the mobile

slide (e) well against the edge of the door, sliding the

machine up to the edge markings. For faster operation,

start cutting at one of the ends and work towards the

other in a single go (Fig. 7). To make the recess that

locates the intermediate lug, tilt the milling attachment

slightlym rocking the guide square (e) on one of the

ends so that the milling area is shifted sideways to that

required for the recess (Fig. 9).

The ends of the milled area can be seen through the

open section of the support base.

USE AS A SPINDLE SHAPER (Fig. 11)

If the whole mobile slide assembly (e) is removed

from the machine, the milling attachment becomes a

conventional spindle shaper with the support base

(m) for all kinds of artistic shaping work and mar-

quetry or straight-line shaping by sliding the edge of

the base along a rule fixed to the work surface. The

shaper also has the appropriate speed and clamp for

working as a grinder, with wheels of 6 mm ø shaft, if

the base (m) is first removed.

USE AS A MILLING ATTACHMENT FOR FORMICA

EDGES (Fig. 12)

The machine, fitted with the cross-wise adjustable

mobile slide (e), is ideal for straight milling formica

sheets glued on board, to make them level with the edge

of the board. A perfect finish is obtained by using a

tapered milling cutter with hard metal tips.

MILLING HEAD INSTALLATION

WARNING! The mains cable must be removed from the

socket before any adjustments are made to the machine.

It is recommended that protective gloves be worn when

installing or removing milling heads.

1. To install the milling head, press the spindle lock of

shaft B until it coincides with the shaft planes.

2. A 22-mm spanner should be used to loosen clip

fixing nut D in an anticlockwise direction.

3. Insert the milling head so that the shaft enters the

clip by a minimum of 20 mm (shaft length).

4. Tighten the clip fixing nut D with the spanner and

release the clip-carrier shaft support lever B.

PRECAUTION: Do not tighten clip fixing nut D without a

milling head inserted into the clip.

DUST EXTRACTION

WARNING! Always make sure that the tool is switched

off and unplugged before fitting or removing any dust

extraction device.

Dust extraction keeps the workplace clean, prevents

dust build-up in the air and facilitates waste elimination.

These milling machines are fitted with adapter, which

can be coupled to a universal vacuum aspirator or other

dust suction device.

CAUTION: A suction extractor should always be used

that has been designed in accordance with the applica-

ble directives in relation to dust emission when milling

wood. The flexible hoses of conventional vacuum clean-

ers fit directly onto the dust extraction nozzle.

The aspirator should be suitable for the material

being worked.

A special aspirator must be employed in those cases

where dry harmful or carcinogenic dust is produced.

In situations where prolonged wood operations are

performed or machines are used industrially with

materials that produce dust that is harmful to health,

the machine must be connected to a suitable external

aspiration device.

NOISE AND VIBRATION

This tool has been designed and made to reduce noise

to a minimum. However, in spite of this, in certain

circumstances the maximum noise level in the place

of work could exceed 85 dBA. In this case, the op-

erator should wear ear protection.

The machine’s noise and vibration levels, measured in

compliance with EN60745-1, usually reach:

Acoustic pressure = 83 dB(A)

Sound-power level = 96 dB(A)

Use ear protection!

Vibration acceleration = 2.5 m/s

ACCESSORIES

Accessories and their corresponding order number can

be found in our catalogues.

MAINTENANCE AND CARE

WARNINGAlways unplug the machine before carrying

out work on it.

- Tool inspection: Using a blunt cutting tool leads to

less efficient work and could damage the motor,

therefore cutting tools should be sharpened or re-

placed as soon as any wear is noticed. Daily: Clean

the tool holder.

- The milling heads must always be maintained sharp

for optimum work results.

- Inspect the mounting screws: Regularly inspect all

the mounting screws and ensure they are firmly tight-

ened. Should any screw be loose, tighten it immedi-

ately. Failure to do so could put you at serious risk.

- Motor maintenance: Take the utmost care to ensure

that the motor winding is not damaged and does not

become damp with oil or water.

- Brush replacement: The brushes disconnect auto-

matically and should be replaced after 150 - 200 hours

use or when they are less than 10 mm long. Have

them replaced by an Official Service Centre.

- Clean the machine thoroughly after each use with a

blast of dry air.

- The vents of the machine should be kept clear at all

times.

- Check that the mains lead is in good condition. If it is

not, take it to an Official Service Centre to have it re-

placed.

- Use only Felisatti accessories and spares. The

parts the changing of which is not covered in this

instruction manual, should be replaced in a Fe-

Felisatti RF30 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info