Bedienungsanleitung Felisatti SCF190 (Seite 3 von 40) (Deutsch, Englisch, Französisch, Italienisch, Portugiesisch, Spanisch)

502496

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

MACHINE-SPECIFIC SAFETY WARNINGS

● DANGER: Keep hands away from cutting area and the

blade. Keep your second hand on auxiliary handle, or motor

housing. If both hands are holding the saw, they cannot be

cut by the blade.

● Do not reach underneath the workpiece.

The guard cannot protect you from the blade below the

workpiece.

● Adjust the cutting depth to the thickness of the workpiece.

Less than a full tooth of the blade teeth should be visible

below the workpiece.

● Never hold the workpiece being cut in your hands or

across your leg. Secure the workpiece to a stable platform.

It is important to support the work properly to minimize body

exposure, blade binding, or loss of control.

● Hold the power tool only by the insulated gripping surfaces

when performing an operation where the cutting tool may

contac hidden wiring or its own cord. Contact with a “live”

wire will also make exposed metal parts of the power tool

“live” and shock the operator.

● When ripping always use a rip fence or straight edge

guide. This improves the accuracy of cut and reduces the

chance of blade binding.

● Always use blades with correct size and shape (diamond

versus round) of arbour holes. Blades that do not match the

mounting hardware of the saw will run eccentrically, causing

loss of control.

● Never use damaged or incorrect blade washers or bolt.

The blade washers and bolt were specially designed for your

saw, for optimum performance and safety of operation.

● Causes and operator prevention of kickback:

– Kickback is a sudden reaction to a pinched, bound or

misaligned saw blade, causing an uncontrolled saw to lift up

and out of the workpiece toward the operator.

– When the blade is pinched or bound tightly by the kerf

closing down, the blade stalls and the motor reaction drives

the unit rapidly back toward the operator.

– If the blade becomes twisted or misaligned in the cut,

the teeth at the back edge of the blade can dig into the top

surface of the wood causing the blade to climb out of the kerf

and jump back toward the operator.

Kickback is the result of saw misuse and/or incorrect

operating procedures or conditions and can be avoided by

taking proper precautions as given below.

● Maintain a rm grip with both hands on the saw and

position your arms to resist kickback forces. Position your

body to either

side of the blade, but not in line with the blade. Kickback

could cause the saw to jump backwards, but kickback forces

can be controlled by the operator, if proper precautions are

taken.

● When blade is binding, or when interrupting a cut for any

reason, release the trigger and hold the saw motionless

in the material until the blade comes to a complete stop.

Never attempt to remove the saw from the work or pull the

saw backward while the blade is in motion or kickback may

occur.

Investigate and take corrective actions to eliminate the cause

of blade binding.

● When restarting a saw in the workpiece, centre the saw

blade in the kerf and check that saw teeth are not engaged

into the material.

If saw blade is binding, it may walk up or kickback from the

workpiece as the saw is restarted.

● Support large panels to minimise the risk of blade pinching

and kickback. Large panels tend to sag under their own

weight. Supports must be placed under the panel on both

sides, near the line of cut and near the edge of the panel.

● Do not use dull or damaged blades. Unsharpened or

improperly set blades produce narrow kerf causing excessive

friction, blade binding and kickback.

● Blade depth and bevel adjusting locking levers must be

tight and secure before making cut. If blade adjustment shifts

while cutting, it may cause binding and kickback.

● Use extra caution when making a “plunge cut” into existing

walls or other blind areas.

The protruding blade may cut objects tha can cause

kickback.

● Check lower guard for proper closing before each use. Do

not operate the saw if lower guard does not move freely and

close instantly. Never clamp or tie the lower guard into the

open position. If saw is accidentally dropped, lower guard

may be bent.

Raise the lower guard with the retracting handle and make

sure it moves freely and does not touch the blade or any

other part, in all angles and depths of cut.

● Check the operation of the lower guard spring. If the

guard and the spring are not operating properly, they must

be serviced before use. Lower guard may operate sluggishly

due to damaged parts, gummy deposits, or a build-up of

debris.

● Lower guard should be retracted manually only for special

cuts such as “plunge cuts” and “compound cuts”. Raise lower

guard by retracting handle and as soon as blade enters the

material, the lower guard must be released. For all other

sawing, the lower guard should operate automatically.

● Always observe that the lower guard is covering the blade

before placing saw down on bench or oor. An unprotected,

coasting blade will cause the saw to walk backwards, cutting

whatever is in its path. Be aware of the time it takes for the

blade to stop after switch is released.

● Use the appropriate riving knife for the blade being used.

For the riving knife to work, it must be thicker than the body of

the blade but thinner than the tooth set of the blade.

● Adjust the riving knife as described in this

instruction manual. Incorrect spacing, positioning and

alignment can make the riving knife ineffective in preventing

kickback.

● Always use the riving knife except when plunge cutting.

Riving knife must be replaced after plunge cutting. Riving

knife causes interference during plunge cutting and can

create kickback.

● For the riving knife to work, it must be engaged in the

workpiece. The riving knife is ineffective in preventing

kickback during short cuts.

● Do not operate the saw if riving knife is bent. Even a light

interference can slow the closing rate of a guard.

● Do not reach into the saw dust ejector with your hands.

They could be injured by rotating parts.

● Do not work overhead with the saw. In this manner you do

not have sufcient control over the power tool.

● Use suitable detectors to determine if utility lines are

hidden in the work area or call the local utility company for

assistance.

Contact with electric lines can lead to re and electric shock.

Damaging a gas line can lead to explosion. Penetrating a

water line causes property damage or may cause an electric

shock.

● Do not operate the power tool stationary. It is not designed

for operation with a saw table.

● Do not use high speed steel (HSS) saw blades. Such saw

blades can easily break.

● Do not saw ferrous metals. Red hot chips can ignite the

Felisatti SCF190 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info