502496

Felisatti SCF190 Seite 6

6
Zoom out
Zoom in
Vorherige Seite
1/40
Nächste Seite
6
on the xed guard of the machine indicates the cutting
direction of the teeth).
SETTINGS
1. Cutting depth setting
For a clean perfect cut, the cutting depth should be adjusted
to the thickness of the wood to be worked on, so that the saw
blade protrudes a tooth’s height from the material.
To adjust the cutting depth, loosen the wing nut G and move
the machine upwards or downwards. The scale printed on
the parallel guide indicates the cutting depth.
2. Cutting angle setting
It can cut vertically and with an inclination of up to 45º. The
angle is adjusted by loosening the wing nut M and according
the scale printed on the base.
3. Riving knife adjustment
WARNING: The riving knife F prevents the blade from seizing
up duriing cutting operations and shold alwyas be used for
safety reasons.
The machine is supplied with the riving knife adjusted. When
tting a new blade, follow the steps below for readjustment:
1. Raise the mobile guard C and loosen rhe screw button
B.
2. Move the wedge through the slot to a distance from the
teeth tip and a cutting depth from same of 2 to 3 mm (máx. 5
mm).
3. Tighten the screw B and the machine is ready to work.
4. Lateral stop adjustment
For parallel cutting, use the lateral stop I.
Cutting width is adjusted with the scale or according to the
plotting.
Tighten the wing nut H to work with the lateral stop.
DUST EXTRACTION
WARNING! Always make sure that the tool is switched off
and unplugged before tting or removing any dust extraction
device.
Dust extraction keeps the workplace clean, prevents dust
build-up in the air and facilitates waste elimination.
These saws are equipped with a dust extraction hole N
to which an adapter can be tted (suppied as an optional
accessory).
A universal vacuum cleaner may be tted or any dust
extraction device.
CAUTION: Always use a vacuum extractor designed in
accordance with the applicable Guidelines on sawdust
emission. The exible hoses of conventional vacuum
cleaners t directly onto the dust extraction nozzle.
ACCESSORIES
Accessories and their corresponding order number can be
found in our catalogues.
MAINTENANCE AND CARE
WARNING! Always unplug the machine before carrying out
work on it.
- Checking the saw blade: Deposits of resin and glue on
the saw blade cause inefcient cutting. To avoid them, always
clean the blade immediately after use.
- Inspect the mounting screws: Regularly inspect all
the mounting screws and ensure they are rmly tightened.
Should any screw be loose, tighten it immediately. Failure to
do so could put you at serious risk.
- Motor maintenance: Always take the greatest care over
this and make sure that the motor winding is not damaged
and does not become wet with oil or water.
- The vents should always be kept clean and free of
obstacles.
- Clean the machine thoroughly after each use. Blast the
motor regularly with compressed air.
- Check that the mains lead is in good condition. If it is not,
take it to an Ofcial Service Centre to have it replaced.
- Brush replacement: Brushes must be replaced when
length reaches 8 mm or less. To do so, please contact an
authorized after sales service center. We recommend that
every other time you take a tool to an after sales service
center for carbon brushes replacement you also order a
general maintenance (cleaning and lubrication).
Use only Felisatti accessories and spares. Parts the changing
of which is not covered in this instruction manual, should be
replaced in a Felisatti Ofcial Service Centre (See Warranty/
Ofcial Service Centre address leaet).
WARRANTY
See general warranty conditions printed on the attached
sheet.
NOISE AND VIBRATION
This tool has been designed and made to reduce noise to a
minimum. However, in spite of this, in certain circumstances
the maximum noise level in the place of work could exceed 85
dBA. In this case, the operator should wear ear protection.
The machine’s noise and vibration levels, measured in
compliance with EN 50144, usually reach:
Acoustic pressure = 96 dB(A)
Sound-power level = 109 dB(A)
Use ear protection!
Vibration acceleration = 2.7 m/s
2
… 6 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Felisatti SCF190 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info