Bedienungsanleitung Ferm AGM1049 - FAG-125-500 (Seite 7 von 16) (Englisch)

763248

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Ferm

Mains plug replacement (UK only)

If the moulded 3-pin plug attached to the unit is

damaged and needs replacing, it is important that

it is correctly destroyed and replaced by an

approved BS 1363/5A fused plug and that the

following wiring instructions are followed.

The wires in the mains cable are coloured in

accordance with the following code:

blue neutral

brown live

As the colours of the wires in the mains cable of

the unit may not correspond to the coloured

markings identifying the terminals in the plug,

proceed as follows:

- The wire which is coloured blue must be

connected to the terminal which is marked

with the letter N or coloured black.

- The wire which is coloured brown must be

connected to the terminal which is marked

with the letter L or coloured red.

Technical data

Mains voltage 230-240 V~

Mains frequency 50 Hz

Power input 500 W

No-load speed 11,000 /min

Grinding disc Ø 125 mm

Bore Ø 22 mm

Spindle thread M14

Weight 1.5 kg

Sound pressure (Lpa) 80 dB(A)

Acoustic power (Lwa) 91 dB(A)

Uncertainty (K) 3 dB(A)

Vibration 3.23 m/s2

Uncertainty (K) 1.5 m/s2

Vibration level

The vibration emission level stated in this

instruction manual has been measured in

accordance with a standardised test given in EN

60745; it may be used to compare one tool with

another and as a preliminary assessment of

exposure to vibration when using the tool for the

applications mentioned

- using the tool for different applications, or with

different or poorly maintainted accessories,

may significantly increase the exposure level

- the times when the tool is switched off or when

it is running but not actually doing the job, may

signifi cantly reduce the exposure level

Protect yourself against the effects of

vibration by maintaining the tool and its

accessories, keeping your hands warm, and

organizing your work patterns

Wear ear and eye protection

Description

(fig. A)

Your angle grinder has been designed for grinding

and cutting masonry and steel.

This machine, in combination with the

included grinding guard, is only suitable

for grinding operations. Cutting

operations with bonded abrasive cut-off

wheels are only allowed when a cut-off

guard (Fig D, available as optional

accessory 300802) is used.

1. On/off switch

2. Spindle lock button

3. Spindle

4. Guard

5. Main grip

6. Auxiliary grip

Assembly

Before assembly, always switch off the

machine and remove the mains plug from

the mains.

Mounting and removing the guard

(fig. B)

Do not use the machine without the

guard.

Mounting

Place the machine on a table with the spindle •

(3) facing upwards.

Keep the spindle lock button (2) pressed and •

remove the flange (7) using the flange key (8).

If necessary, remove the grinding disc (9).•

Remove the flange (10).•

Mount the guard (4). Secure the guard (4) by •

tightening the screw (11) and the nut (12).

Mount the flange (10).•

If necessary, mount the grinding disc (9).•

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm AGM1049 - FAG-125-500 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info