Bedienungsanleitung Ferm AGM1084P (Seite 6 von 156) (Alle Sprachen)

762283

Zoom out

Zoom in

Vorherige Seite

1/156

Nächste Seite

p) Do not use accessories that require liquid

coolants. Using water or other liquid coolants

may result in electrocution or shock.



Kickback is a sudden reaction to a pinched or

snagged rotating wheel, backing pad, brush or

any other accessory. Pinching or snagging causes

rapid stalling of the rotating accessory which in

turn causes the uncontrolled power tool to be

forced in the direction opposite of the accessory’s

rotation at the point of the binding.

For example, if an abrasive wheel is snagged or

pinched by the workpiece, the edge of the wheel

that is entering into the pinch point can dig into the

surface of the material causing the wheel to climb

out or kick out. The wheel may either jump toward

or away from the operator, depending on direction

of the wheel’s movement at the point of pinching.

Abrasive wheels may also break under these

conditions.

Kickback is the result of power tool misuse and/or

incorrect operating procedures or conditions and

can be avoided by taking proper precautions as

given below.

a) Maintain a firm grip on the power tool and

position your body and arm to allow you to resist

kickback forces. Always use auxiliary handle,

if provided, for maximum control over kickback

or torque reaction during start-up. The operator

can control torque reactions or kickback forces,

if proper precautions are taken.

b) Never place your hand near the rotating acces-

sory. Accessory may kickback over your hand.

c) Do not position your body in the area where

power tool will move if kickback occurs.

Kickback will propel the tool in direction

opposite to the wheel’s movement at the point

of snagging.

d) Use special care when working corners, sharp

edges etc. Avoid bouncing and snagging the

accessory. Corners, sharp edges or bouncing

have a tendency to snag the rotating accessory

and cause loss of control or kickback.

e) Do not attach a saw chain woodcarving blade

or toothed saw blade. Such blades create

frequent kickback and loss of control.



• Check that the maximum speed indicated on

the disc corresponds to the maximum speed

of the machine. The speed of the machine

must not exceed the value on the disc.

• Make sure that the dimensions of the disc cor-

res pond to the specifications of the machine.

• Make sure that the disc has been mounted

and fastened properly. Do not use reducing

rings or adapters to make the disc fit properly.

• Never use this machine single handed. Always

use both hands to operate the machine.

• Do not touch any rotating parts.

•

Make sure the wool bonnet is not contacting

the workpiece before the machine is switched

on.

• Do not touch the workpiece immediately after

operation. It may be hot.

• Warning: The wheel still rotates after the

machine has been switched off

• Hold the machine by the insulated grips when

performing an operation where contact can be

made with hidden wiring or its own cord.

• Before use, inspect the disc for any damage.

Do not use discs which are crack-ed, ripped or

otherwise damaged.

• Before use, let the machine run idle for 30

seconds. Immediately switch off the machine

in case of abnormal vibrations or occurrence

of another defect. Carefully inspect the

machine and disc before switching the

machine on again.

• Always wear safety goggles and hearing

protection.

• Ensure that mounted wheels and points are

fitted in accordance with the manufacturer’s

instructions.

• For tools intended to be fitted with threaded

hole wheel, ensure that the thread in the

wheel is long enough to accept the spindle

length.

• Ensure that ventilation openings are kept clear

when working in dusty conditions. If it should

become nessesary to clear dust, first

disconnect the tool from the mains supply (use

non metallic objects) and avoid damaging

internal parts.

• Though poor conditions of the electrical

mains, shortly voltage drops can appear when

starting the equipment. This can influence

other equipment (eq. blinking of a lamp). If the

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm AGM1084P Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info