Bedienungsanleitung Ferm AGM1089P (Seite 9 von 16) (Englisch)

763843

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

ASSEMBLY

Before assembly, always switch off the

machine and remove the mains plug from

the mains.

Mounting and removing the guard (fig. B)

Do not use the machine without the

guard.

Mounting

• Place the machine on a table with the spindle

(3) facing upwards.

• Keep the spindle lock button (2) pressed and

remove the flange (7) using the flange key (8).

• If necessary, remove the grinding disc (9).

• Remove the flange (10).

• Mount the guard (4). Secure the guard (4) by

tightening the screw (11) and the nut (12).

• Mount the flange (10).

• If necessary, mount the grinding disc (9).

• Keep the spindle lock button (2) pressed and

mount the flange (7) using the flange key (8).

Removing

• Place the machine on a table with the spindle

(3) facing upwards.

• Keep the spindle lock button (2) pressed and

remove the flange (7) using the flange key (8).

• If necessary, remove the grinding disc (9).

• Remove the flange (10).

• Remove the guard (4) by loosening the screw

(11) and the nut (12).

• Mount the flange (10).

• If necessary, mount the grinding disc (9).

• Keep the spindle lock button (2) pressed and

mount the flange (7) using the flange key (8).

Mounting and removing the grinding disc

(fig.B)

Do not use the machine without the

guard.

Mounting

• Place the machine on a table with the guard (4)

facing upwards.

• Keep the spindle lock button (2) pressed and

remove the flange (7) using the flange key (8).

• Mount the grinding disc (9).

• Keep the spindle lock button (2) pressed and

mount the flange (7) using the flange key (8).

Removing

• Place the machine on a table with the guard (4)

facing upwards.

• Keep the spindle lock button (2) pressed and

remove the flange (7) using the flange key (8).

• Remove the grinding disc (9).

• Keep the spindle lock button (2) pressed and

mount the flange (7) using the flange key (8).

Mounting and removing the auxiliary grip

(fig.C)

Mounting

• Tighten the auxiliary grip (6) into one of the

mounting holes (13).

Removing

• Loosen the auxiliary grip (6) from the mounting

hole (13).

USE

Switching on and off (fig. A)

• To switch on the machine in continuous mode,

flip the On/Off switch (1) to ‘Off’

• To switch off the machine, flip the On/Off

switch (1) to ‘Off’

Hints for optimum use

• Clamp the workpiece. Use a clamping device

for small workpieces.

• Draw a line to define the direction in which to

guide the grinding disc.

• Hold the machine with both hands.

• Switch on the machine.

• Wait until the machine has reached full speed.

• Place the grinding disc on the workpiece.

• Slowly move the machine along the pre-drawn

line, firmly pressing the grinding disc against

the workpiece.

• Do not apply too much pressure on the

machine. Let the machine do the work.

• Switch off the machine and wait for the

machine to come to a complete standstill

before putting the machine down.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm AGM1089P Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info