Bedienungsanleitung Ferm AGM1102 (Seite 7 von 80) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Finnisch)

764188

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

Electrical safety

Always check that the voltage of the

power supply corresponds to the voltage

on the rating plate.

• Do not use the machine if the mains cable or

the mains plug is damaged.

• Only use extension cables that are suitable

for the power rating of the machine with a

minimum thickness of 1.5 mm2. If you use a

extension cable reel, always fully unroll the

cable.

Technical data

Mains voltage 220-240 V~

Mains frequency 50 Hz

Power input 500 W

No-load speed 12,000/min

Grinding disc Diameter 125 mm

Bore 22.2 mm

Spindle thread M14

Weight 1.69 kg

Noise and vibration

Sound pressure (Lpa) (K=3dB) 86 dB(A)

Acoustic power (Lwa) (K=3dB) 97 dB(A)

Vibration (K=1.5 m/s2) 2.48 m/s2

Vibration level

The vibration emission level stated in this

instruction manual has been measured in

accordance with a standardised test given in

EN 60745; it may be used to compare one tool

with another and as a preliminary assessment of

exposure to vibration when using the tool for the

applications mentioned

- using the tool for different applications, or with

different or poorly maintainted accessories,

may significantly increase the exposure level

- the times when the tool is switched off or when

it is running but not actually doing the job, may

significantly reduce the exposure level

Protect yourself against the effects of vibration by

maintaining the tool and its accessories, keeping

your hands warm, and organizing your work

patterns

Wear hearing protection.

DESCRIPTION (FIG. A)

Your angle grinder has been designed for grinding

and cutting masonry and steel.

1. On/off switch

2. Spindle lock button

3. Spindle

4. Guard

5. Main grip

6. Auxiliary grip

ASSEMBLY

Before assembly, always switch off the

machine and remove the mains plug from

the mains.

Mounting and removing the guard & grinding

disc (fig. B)

Do not use the machine without the guard.

Mounting

• Place the machine on a table with the spindle

(3) facing upwards.

• Keep the spindle lock button (2) pressed and

remove the flange (7) using the flange key (8).

• If necessary, remove the grinding disc (9).

• Remove the flange (10).

• Mount the guard (4). Secure the guard (4) by

tightening the screw (11) and the nut (12).

• Mount the flange (10).

• If necessary, mount the grinding disc (9).

• Keep the spindle lock button (2) pressed and

mount the flange (7) using the flange key (8).

Removing

• Place the machine on a table with the spindle

(3) facing upwards.

• Keep the spindle lock button (2) pressed and

remove the flange (7) using the flange key (8).

• If necessary, remove the grinding disc (9).

• Remove the flange (10).

• Remove the guard (4) by loosening the screw

(11) and the nut (12).

• Mount the flange (10).

• If necessary, mount the grinding disc (9).

• Keep the spindle lock button (2) pressed and

mount the flange (7) using the flange key (8).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm AGM1102 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info