Bedienungsanleitung Ferm BGM1022 (Seite 8 von 88) (Alle Sprachen)

762289

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

sanded at the ends of the sanding belt. Work

pieces which are longer than the sanding machine

can be sanded by removing the fence.

NB: To prevent splintering, wood always needs

to be sanded in the longitudinal direction of the

grain.

To treat a very soft surface, there is a very handy

method to ‘bring the particles to the surface’.

This is done as follows: wet the already sanded

surface with a cloth or sponge and let it dry well.

Some wood fibres will swell up more than others,

which leads to a rougher surface than before.

Now the higher particles are treated with fine

sanding paper, the result is a remarkably smooth

surface. This method should not be applied with

varnished wood, however, because the varnish

may come loose because of the moisture.

5. MAINTENANCE

Before cleaning and maintenance,

always switch off the machine and

remove the mains plug from the mains.

Clean the machine casings regularly with a soft

cloth, preferably after each use. Make sure that

the ventilation openings are free of dust and

dirt. Remove very persistent dirt using a soft

cloth moistened with soapsuds. Do not use any

solvents such as gasoline, alcohol, ammonia,

etc. Chemicals such as these will damage the

synthetic components.

Replace power cords

If the supply cord is damaged, it must be replaced

by the manufacturer, its service agent or similarly

qualified persons in order to avoid a hazard.

Mains plug replacement (UK only)

If the moulded 3-pin plug attached to the unit is

damaged and needs replacing, it is important

that it is correctly destroyed and replaced by

an approved BS 1363/7A fused plug and that

the following wiring instructions are followed.

The wires in the mains cable are coloured in

accordance with the following code:

• blue neutral

• brown live

As the colours of the wires in the mains cable

of the unit may not correspond to the coloured

markings identifying the terminals in the plug,

proceed as follows:

• The wire which is coloured blue must be

connected to the terminal which is marked

with the letter N or coloured black.

• The wire which is coloured brown must be

connected to the terminal which is marked

with the letter L or coloured red.

ENVIRONMENT

Faulty and/or discarded electrical or

electronic apparatus have to be

collected at the appropriate recycling

locations.

Only for EC countries

Do not dispose of power tools into domestic

waste. According to the European Guideline

2012/19/EU for Waste Electrical and Electronic

Equipment and its implementation into national

right, power tools that are no longer usable must

be collected separately and disposed of in an

environmentally friendly way.

WARRANTY

The warranty conditions can be found on the

separately enclosed warranty card.

The product and the user manual are subject

to change. Specications can be changed

without further notice.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm BGM1022 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info