Bedienungsanleitung Ferm BJM1001 (Seite 8 von 108) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

510089

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite



Adjusting the cutting depth

Fig.B

• Move the motor base (15) as far as possible

backwards.

• Set the cutting depth by turning the cutting

depth adjustment knob (7).

• Move the motor base forwards and check if

the pin (A) will fall in the notch of the

adjustment knob.

The following table shows the relationship of the

markings on the adjustment knob to cutting depth,

thickness of material and associated biscuit

dowel.

Marking Thickness Biscuit Cutting

of material Dowel depth in mm

0 8-12 mm No. 0 8.0

10 12-15 mm No. 10 10.0

20 > 15 mm No. 20 12.3

S - Simplex 13.0

D - Duplex 14.7

Max. - - 18.0

Adjusting the cutting angle

Fig. C

• The cutting angle can be set by unlocking the

clamping lever (8) and put the angle stop (4)

in the required angle.

• Should the clamping lever be in the way when

working with the tool, then pull the clamping

lever out and fasten it in a different position

without changing the cutting angle.

Adjusting the height

Fig. D

• The correct height can be set by unlocking the

clamping lever (9) and turning the knob for the

height adjustment (10) to the desired height

with aid of the scale (11).

• The height must corresponds to half of the

material thickness of the working piece, the

groove for the biscuit dowel must always be in

the middle of the working piece.

• Should the clamping lever be in the way when

working with the tool, then pull the clamping

lever out and fasten it in a different position

without changing the height.



Prior to mounting an accessory always

unplug the tool.

Mounting the saw blade

Fig. E

• Loosen the allen screw (16) with the supplied

allen wrench and open the top of the base

plate

• Press the spindle lock and turn the spindle

(17) until it engages in the lock. Keep the

spindle lock pressed during this procedure.

• Remove the flange nut (18) from the spindle

using the wrench (19).

• Position the saw blade (20) on the flange (21).

• Be aware that the arrow on the sawblade

indicates the same direction as the arrow on

the inside of the housing.

• Place the flange nut (18) on the spindle (17)

and tighten it with the wrench.

• The flange nut has two sides. One for

sawblades with bore 20 mm and the otherside

for sawblades with bore 22 mm.

• Take care that the flange nut will be placed

with the correct side on the spindle.

• Release the spindle lock and check that the

spindle is unlocked by rotating it.

• Close the top of the base plate and fasten the

allen screw (16) with the supplied allen

wrench.

Make sure that the top of the base plate

is securely closed before operating the

machine.

Mounting the dust bag

Fig. A

For dust extraction the dust bag (14) can be used.

Insert the dust bag (14) into the vacuuming

connection (13). Empty the dust bag regularly so

that the vacuuming performance remains intact.



Never use the spindle lock while the

machine is working.

Switching on and off

• To switch the machine on slide the on/off

switch forwards.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm BJM1001 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info