Bedienungsanleitung Ferm BJM1001 (Seite 9 von 108) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

510089

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

• To switch the machine off, depress the on/off

switch, the switch will automatically move to

the ‘off’ position.

Never use the spindle lock to stop the

motor.

Marking the workpieces

Fig. F

Before starting with the Biscuit Jointer the

workpieces must be marked as following.

• Place the two workpieces, which must be

connected, on top of each other.

• Fasten the workpieces and mark the center of

the groove.

• The space between two grooves should be

10-15 cm, this doesn’t concerns for smaller

workpieces. Smaller workpieces don’t have to

be marked.

Positioning of the machine

Based on the size of the workpieces the machine

can be positioned in several ways.

Large workpieces

Fig. G

• Place the machine near the workpiece.

• The middle of the base plate (this point is

marked on the base plate) must facing the

centre of the groove in the workpiece (see

marking the workpiece).

Small workpieces

Fig. H

• Place the machine near the workpiece.

• The side of the machine must be facing the

side of the workpiece.

Workpieces thinner than 16 mm

Fig. I

• Place the machine near the workpiece.

• Place the adjustment plate (5) on the angle

stop (4).

• Take care for setting the height, the groove for

the biscuit dowel must be in the middle of the

workpiece.

For workpieces thinner than 16 mm it is not

possible to make the groove for the biscuit dowel

in the middle of the workpiece without the aid of

the adjustment plate.

Sawing grooves

• Move the motor base backward.

• Place the machine near the workpiece.

• Position the machine (see positioning of the

machine)

• Hold the machine with both hands and switch

the machine on.

• Push the motor base carefully forward as far

as possible.

• Move the motor base backward and switch

the machine off.

Move the machine in the same direction

as the direction of rotation. See arrow

on top of the machine (16).

Joining the workpieces

When the grooves in both workpieces have been

made the workpieces can be joined together.

• Put glue in both grooves.

• Place the biscuit dowel in the groove of one

workpiece.

• Place the other workpiece on the biscuit

dowel.

• Fasten the workpieces and wait till the glue is

dry.

User tip for connecting two workpieces

Fig. K

• Saw a groove as big as one biscuit into the

first workpiece

• Place the biscuit with good glue (according

the material) into the groove

• Saw a longer groove into the other workpiece

• Now both workpieces can be positioned easily

towards each other (clearance to correct)

• Fasten the workpieces and wait till the glue is

dry

Checking the cutting depth

Fig. J

Always check the cutting depth after mounting a

saw blade.

• Disconnect the plug from the socket.

• Move the motor base (15) as far as possible

backwards.

• Set the cutting depth in the maximum position

by turning the depth adjustment knob (7).

• Move the motor base forwards till the pin (A)

will fall in the notch of the adjustment knob (7).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm BJM1001 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info