Bedienungsanleitung Ferm BSM1024 (Seite 5 von 108) (Alle Sprachen)

764022

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

• Do not use the machine if the mains cable or

the mains plug is damaged.

• Only use extension cables that are suitable for

the power rating of the machine with a minimum

thickness of 1.5 mm2. If you use a extension

cable reel, always fully unroll the cable.

Mains plug replacement (UK only)

If the moulded 3-pin plug attached to the unit is

damaged and needs replacing, it is important

that it is correctly destroyed and replaced by an

approved BS 1363/5A fused plug and that the

following wiring instructions are followed.

The wires in the mains cable are coloured in

accordance with the following code:

blue neutral

brown live

As the colours of the wires in the mains cable

of the unit may not correspond to the coloured

markings identifying the terminals in the plug,

proceed as follows:

- The wire which is coloured blue must be

connected to the terminal which is marked

with the letter N or coloured black.

- The wire which is coloured brown must be

connected to the terminal which is marked

with the letter L or coloured red.

TECHNICAL DATA

BSM1024

Mains voltage 230 V~

Mains frequency 50 Hz

Power input 900 W

No-load speed 380 /min

Sanding belt size 75x533 mm

Sanding pad size 76x135 mm

Protection class IP 20

Weight 3.65 kg

NOISE AND VIBRATION

Sound pressure (Lpa) 86 dB(A) K=3dB

Acoustic power (Lwa) 97 dB(A) K=3dB

Vibration (main grip) 3.92 m/s2 K=1.5 m/s2

Wear hearing protection.

Vibration level

The vibration emission level stated in this instruction

manual has been measured in accordance with

a standardised test given in EN 60745; it may be

used to compare one tool with another and as a

preliminary assessment of exposure to vibration

when using the tool for the applications mentioned

- using the tool for different applications, or with

different or poorly maintainted accessories,

may significantly increase the exposure level

- the times when the tool is switched off or when

it is running but not actually doing the job, may

signifi cantly reduce the exposure level

Protect yourself against the effects of vibration by

maintaining the tool and its accessories, keeping

your hands warm, and organizing your work

patterns

DESCRIPTION (FIG.A)

Your belt sander has been designed for rough

sanding applications on wood, metal, plastics and

painted surfaces.

1. On/off switch

2. Lock-on button

3. Sanding pad

4. Sanding belt roller

5. Clamping lever for sanding belt

6. Centring knob for sanding belt

7. Main grip

8. Auxiliary grip

9. Dustbag connection

10. Carbon brush holder

11. V-belt cover

ASSEMBLY

Before assembly, always switch off the

machine and remove the mains plug from

the mains.

Mounting and removing the sanding belt (fig.A

& B)

Mounting

• Place the machine on its side with the V-belt

cover (11) facing downwards.

• Release the clamping lever (5).

• Mount a sanding belt (12) with the required

grain size around the sanding pad (3) and the

sanding belt rollers (4). Make sure that the

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm BSM1024 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info