Bedienungsanleitung Ferm BSM1024 (Seite 6 von 108) (Alle Sprachen)

764022

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

arrow on the inside of the sanding belt points

in the same direction as the arrow on the

housing.

- Use a coarse sanding belt (grain 50) for

sanding rough, uneven surfaces.

- Use a medium sanding belt (grain 80) for

removing the remaining scratches from the

coarse sanding belt.

- Use a fine sanding belt (grain 120) for finishing

surfaces.

• Make sure that the sanding belt (12) is straight

and centred around the sanding pad (3) and

the sanding belt rollers (4).

• Tighten the clamping lever (5).

Removing

• Place the machine on its side with the V-belt

cover (11) facing downwards.

• Release the clamping lever (5).

• Remove the sanding belt (12).

• Tighten the clamping lever (5).

Centring the sanding belt (fig.B)

If the sanding belt does not run parallel with the

outer edge of the housing, the sanding belt must

be centred.

• Turn the centring knob (6) clockwise to move

the sanding belt (12) to the inside.

• Turn the centring knob (6) counterclockwise to

move the sanding belt (12) to the outside.

USE

Switching on and off (fig.A)

• To switch on the machine, press the on/off

switch (1).

• To switch the machine to continuous mode,

keep the on/off switch (1) pressed and

simultaneously press the lock-on button (2).

• To switch off continuous mode, press the on/

off switch (1) again.

• To switch off the machine, release the on/off

switch (1).

Dust extraction (fig.C)

• Insert the dustbag (13) into the dustbag

connection (9).

Hints for optimum use

• Clamp the workpiece.

• Hold the machine with one hand on the main

grip and the other hand on the auxiliary grip.

• Switch on the machine.

• Place the sanding belt on the workpiece.

• Slowly move the machine over the workpiece,

firmly pressing the sanding belt against the

workpiece.

• Do not apply too much pressure on the

machine. Let the machine do the work.

• Switch off the machine and wait for the

machine to come to a complete standstill

before putting the machine down.

CLEANING AND MAINTENANCE

Before cleaning and maintenance, always

switch off the machine and remove the

mains plug from the mains.

• Regularly clean the housing with a soft cloth.

• Keep the ventilation slots free from dust and

dirt. If necessary, use a soft, moist cloth to

remove dust and dirt from the ventilation slots.

• Regularly clean the sanding pad and the

sanding belt rollers to avoid inaccuracies

during use.

Replacing the sanding belt (fig.B)

• To remove the old sanding belt (12), proceed

as described in the section “Mounting and

removing the sanding belt”.

• To mount the new sanding belt (12), proceed

as described in the section “Mounting and

removing the sanding belt”.

Checking and replacing the carbon brushes

(fig.A)

The carbon brushes must be checked regularly.

If the carbon brushes are worn, the machine will

start to run unevenly.

Only use the correct type of carbon

brushes.

• Remove the carbon brush holders (10) using a

screwdriver.

• Clean the carbon brushes.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm BSM1024 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info