Bedienungsanleitung Ferm CDM1086 (Seite 7 von 60) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

510091

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

Ferm

Electrical safety

Always check that the voltage on the

battery block corresponds to the voltage

on the rating plate. Also check that your

mains voltage corresponds to the input

voltage of the battery charger.

Class II machine – Double insulation –

You don’t need any earthed plug.

Replacing cables or plugs

Immediately throw away old cables or plugs when

they have been replaced by new ones.

• Remove the battery block when the power tool

is not being used and prior to maintenance.

• The tool is suitable for use as a screwdriver

and drill. Any other application is specifically

excluded.

3. MOUNTING ACCESSORIES

Prior to mounting an accessory always

remove the battery.

Fitting and removing drill cutters

Fig. B

In addition to screwdriver bits with a hexagonal

shaft, this tool can also accommodate drill bits with

a hexagonal shaft.

• Loosen the drill chuck (6) by rotating the hand-

grip (8).

• Insert the shaft of the drill cutter into the chuck.

• Tighten the drill chuck so that the drill cutter is

firmly clamped.

• Rotate the drill chuck in the opposite direction

when you wish to change the cutter.

Connecting and removing the battery

Fig. C

Ensure that the exterior of the battery

block or tool is clean and dry before

connecting the charger.

• Ensure that the direction reversing switch (1,

Fig. A) is in the central position in order to

prevent the appliance from being switched on

unexpectedly.

• Insert the battery (3) into the base of the

appliance, as shown on the illustration. Push

the battery until it latches in.

• Press the locking buttons (2) on both sides

before removing the battery, and disengage

the battery from the base of the appliance.

4. OPERATION

Always follow the safety notes and the

relevant safety code.

Hold the appliance firmly and press the drill

steadily onto the workpiece. Do not overload the

appliance. Only use drills with no visible wear.

Worn drills will have a bad effect on the functioning

of the appliance.

Adjusting the speed

Fig. D

The appliance has two drill speeds.

• For slow drilling or for driving or removing

screws, set the speed selection switch (7) to ‘1’.

• For fast drilling set the speed selection switch

(7) to ‘2’.

Never switch over when the motor is

running!

Adjusting the torque

Fig. E

The appliance has 21 different torque settings with

which to set the power for driving and removing

screws.

• Set the torque adjustment ring (5) to the

desired position. The available torque settings

are indicated on the adjustment ring by the

numbers 1 to 21 and by dots between the

figures to define intermediate settings.

• You should preferably choose a setting as low

as possible when using the screwdriver.

Select a higher setting if the motor slips.

Driving and removing screws

Fig. A

• Set the direction reversing switch (1) to

position ‘’ in order to drive screws.

• Set the direction reversing switch (1) to

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm CDM1086 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info