Bedienungsanleitung Ferm CDM1086 (Seite 8 von 60) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

510091

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

Ferm

position ‘±’ in order to remove screws.

Drilling

• Rotate the torque adjustment ring (5) to the

drilling position.

Ensure that the direction reversing

switch (1) is always set to ‘’ during

drilling.

Switching the device on and off

Fig. A

• Depress the on/off switch (4). It regulates the

speed of the appliance by transmitting power

to the switch.

• Release the on/off switch (4) to halt the drill

chuck immediately, it will no longer run on.

• Move the direction reversing switch (1) to the

centre in order to lock the appliance in its

disabled state.

Only lay down the appliance when it has stopped

running completely. Do not place it on a dusty

surface as particles of dust could get into the

mechanism.

Spirit level

Fig. H

The drill is equipped with a dual reading horizontal/

vertical level to assist in keeping the drill “level”

while drilling horizontal and vertical holes. The

horizontal level (13) is located in the top of the drill

housing. The vertical level (14) is located on the

rear of the drill housing.

To maintain a level drilling position, hold the drill

where the level bubble is centred in the level

indicator circle.

Charging the battery

• The included battery is delivered in partly

charged condition.

• Only use the battery charger in a temperature

range between + 5 °C to + 40 ºC.

• Only use the battery charger in dry, ventilated

rooms.

Charging

Fig. F

One advantage of using Lithium-Ion batteries is

that, until the battery is almost empty, hardly any

power fading is noticeable. The machine can be

used until you start noticing that the power of the

drill is elapsed. The battery is discharged now and

needs to be charged.

Charging the battery

Fig. F

• Place the battery stem (9) into the matching

cavity on top of the charger (10).

• Make sure the battery stem is pressed fully

into the charger as far as it will go.

• Plug the charger into the electrical outlet.

LED indicators

Fig. G

When the battery charger is plugged in and the

battery inserted, the battery charger will begin

charging the battery. The red LED (11) and the

green LED (12) on top of the charger will indicate

the charging status.

• When the charger is plugged in without a

battery inserted, the green LED (12) will be lit

up.

• When a battery is inserted, the red LED (11)

will start blinking, indicating charging has

started.

• When the battery is full, charging will stop and

the green LED (12) will start blinking.

• If the battery is left in the charger, the charger

will go on standby after 2 hours. The green

LED (12) will stop blinking and light up.

When an error occurs the red LED (11)

will be lit up.

If the temperature of the battery is too

high to get charged safely, both the

green LED (12) and red LED (11) will be

lit, indicating charging process is on

hold. Charging will start when the

battery has cooled down.

Lithium-Ion cells can be stored for a

long period without losing much of their

charge. When the machine is not being

used over a longer period of time, it is

best to store the battery in charged

condition.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm CDM1086 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info