Bedienungsanleitung Ferm CDM1114S (Seite 8 von 156) (Alle Sprachen)

632676

Zoom out

Zoom in

Vorherige Seite

1/156

Nächste Seite

3. OPERATING

The battery must be charged before first

use.

Removing the battery from the machine

Fig. B

 Hold the machine (1) firmly with one hand

 Push down the battery unlock button (3)

located on the rear side of the battery (2) with

the other hand.

 Keep pushing this button (3) down and slide

the battery backwards out of the machine, like

shown in Fig. B.

Inserting the battery into the machine

Fig. B

Ensure that the exterior of the battery is

clean and dry before connecting to the

charger or machine.

 

 Insert the battery (2) into the base of the

machine as shown in Fig. B.

 Push the battery further forward until it clicks

into place.

Checking the battery charging status

Fig. C

The included battery is delivered in partly

charged condition.

 To check the battery charge status, push the

button (4) on battery shortly.

 The battery has 4 lights indicating the charge

level, the more lights that burn, the more

charge the battery has left.

 When the lights are burning RED it means

the battery is empty and must be charged

immediately.

Charging the battery (with the charger)

Fig. D

 Take the battery (2) from the machine

 Turn the battery (2) to upside down position

and slide it onto the charger (5) as shown in

Fig. D.

 Push the battery until it is fully pushed into the

slot.

 Plug the charger plug into an electrical outlet

and wait for a while. The LED indicators on

the charger (6) will lighten up and show the

charger status.

LED indicators (6)

Fig.D

The charger has 2 LED indicators (6) which

indicate the status of the charging process:

Red LED

status:

Green LED

status:

Charger status

Off Off No power

Off On

Standby mode:

-No battery is inserted or,

-Battery inserted but charging has

finished more then 2 hours ago

On Off Defective battery

Blinking Off Battery charging in progress

Off Blinking

Battery charging finished, battery

fully charged

On On

Battery is too hot, charging

progress is on hold. Charging will

start automatically after the battery

has cooled down.

 Fully charging the battery may take up to 60

minutes.

 After the battery is fully charged remove the

charger plug from the outlet and remove the

battery from the charger.

 The battery can be stored or directly installed

on the machine.

Lithium-Ion cells can be stored for a long

period without losing much of their

charge. When the machine is not being

used over a longer period of time it is

best to store the battery in charged

condition.

Fitting and removing drills or screwdriver bits

Fig. E

Always remove the battery before

mounting an accessory.

The drill chuck (7) is suitable for drills and

screwdriver bits with round shaft as well as

hexagonal shaft.

 Hold the machine firmly with one hand

 Open the drill chuck (7) by rotating the chuck

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm CDM1114S Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info