Bedienungsanleitung Ferm CDM1114S (Seite 9 von 156) (Alle Sprachen)

632676

Zoom out

Zoom in

Vorherige Seite

1/156

Nächste Seite

sleeve (8) with your other hand in clockwise

direction until it is opened far enough for the

bit to slide in.

 Insert the shaft of the drill or screwdriver bit

 Tighten the drill chuck again by firmly rotating

the chuck sleeve (8) counterclockwise.

 Check if the bit is centered well by shortly

activating the machine´s on/off switch.

Adjusting the gears

Fig. F

Never switch gears when the motor is

running, this will damage your machine.

Never put switch in the middle between

both positions, this will damage your

machine

The machine has 2 drill speeds, which can be

adjusted by sliding the gear switch (9) forward or

backwards. The number on the gear switch (9)

shows which position is chosen.

 Position 1: For slow drilling, large drilling

diameter or screw driving. The machine has

high power at a low speed.

 Position 2: For fast drilling or small drilling

diameter

Adjusting the direction of rotation

Fig. G

 Set the direction switch (10) to position “” in

order to drive screws or to use it for drilling.

 Set the direction switch (10) to position “” in

order to remove screws

Switching the machine on and off

Fig. G

The on/off switch (11) is used for activating the

machine and adjusting rotation speed.

 Pressing the on/off switch (11) will activate

the machine, the further the switch is being

pushed, the faster the drill will turn.

 Releasing the on/off switch (11) will stop the

machine.

 Move the direction reversing switch (10) to the

middle position to lock the movement of the

on/off switch. It cannot be activated in this

position.

Only lay down the machine when it has

stopped running completely. Do not

place it on a dusty surface as particles of

dust could get into the mechanism.

Adjusting the torque

Fig. G

The machine has 23 different torque settings

and a special drill mode to set the power being

transmitted to the chuck.

By rotating the torque adjustment ring (12),

screws can be driven to a predetermined depth,

which is ideal for repetitive work. The higher the

number, the more torque will be transmitted.

 Select a low setting for small screws or soft

work material.

 Select a high setting for large screws, hard

work materials and when removing screws.

 You should preferably choose a setting as

low as possible when driving screws. Select

a higher setting if the motor slips before the

screw is fully tightened.

 For drilling, turn the torque adjustment ring

(12) to the setting for drilling by fully turning it

counterclockwise.

Ensure that the direction switch (10) is

always set to  during drilling.

The machine is equipped with electronic

overload protection function. When the

machine gets overloaded it will shut

down automatically. When this happens,

please wait for at least 5 seconds to let

the overload protection reset itself.

Work light (13)

Fig. A

The machine is equipped with a work light to

illuminate the work location.

 It automatically switches on when the on/off

switch is being pressed.

 It automatically switches off when the on/off

switch is released again.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm CDM1114S Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info