Bedienungsanleitung Ferm CDM1121P (Seite 8 von 144) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

763849

Zoom out

Zoom in

Vorherige Seite

1/144

Nächste Seite

level, the more lights that burn, the more

charge the battery has left.

• When the lights are burning RED it means

the battery is empty and must be charged

immediately.

Charging the battery (with the charger)

Fig. D

• Take the battery (2) from the machine

• Turn the battery (2) to upside down position

and slide it onto the charger (5) as shown in

Fig. D.

• Push the battery until it is fully pushed into the

slot.

• Plug the charger plug into an electrical outlet

and wait for a while. The LED indicators on

the charger (6) will lighten up and show the

charger status.

LED indicators (6)

Fig.D

The charger has 2 LED indicators (6) which

indicate the status of the charging process:

Red LED

status:

Green LED

status: Charger status

Off Off No power

Off On

Standby mode:

-No battery is inserted or,

-Battery inserted but charging has

finished more then 2 hours ago

On Off Defective battery

Blinking Off Battery charging in progress

Off On Battery charging finished, battery

fully charged

On On

Battery is too hot, charging

progress is on hold. Charging will

start automatically after the battery

has cooled down.

• Fully charging the battery may take up to 70

minutes.

• After the battery is fully charged remove the

charger plug from the outlet and remove the

battery from the charger.

• The battery can be stored or directly installed

on the machine.

Lithium-Ion cells can be stored for a long

period without losing much of their

charge. When the machine is not being

used over a longer period of time it is

best to store the battery in charged

condition.

Fitting and removing drills or screwdriver bits

Fig. E

Always remove the battery before

mounting an accessory.

The drill chuck (7) is suitable for drills and

screwdriver bits with round shaft as well as

hexagonal shaft.

• Hold the machine firmly with one hand

• Open the drill chuck (7) by rotating the chuck

sleeve (8) with your other hand in clockwise

direction until it is opened far enough for the

bit to slide in.

• Insert the shaft of the drill or screwdriver bit

• Tighten the drill chuck again by firmly rotating

the chuck sleeve (8) counterclockwise.

• Check if the bit is centered well by shortly

activating the machine´s on/off switch.

Adjusting the gears

Fig. F

Never switch gears when the motor is

running, this will damage your machine.

Never put switch in the middle between

both positions, this will damage your

machine

The machine has 2 drill speeds, which can be

adjusted by sliding the gear switch (9) forward or

backwards. The number on the gear switch (9)

shows which position is chosen.

• Position 1: For slow drilling, large drilling

diameter or screw driving. The machine has

high power at a low speed.

• Position 2: For fast drilling or small drilling

diameter

Adjusting the direction of rotation

Fig. G

• Set the direction switch (10) to position “” in

order to drive screws or to use it for drilling.

• Set the direction switch (10) to position “” in

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm CDM1121P Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info