Bedienungsanleitung Ferm CDM1138 (Seite 9 von 40) (Englisch, Holländisch)

762253

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

Only tighten the handle by hand. Do not

overtighten; this may damage the handle

or its holder

Turn the side handle’s (15) handgrip

anticlockwise a few times so the holder can be

moved over the chuck and placed on the metal

part just behind the torque adjustment ring (12).

2. Make sure the small gap of the handle

aligns with the notch of the metal part on the

machine, as shown on figure C.

3. Turn the handle clockwise to fix it in position.

Fitting and removing drills or screwdriver bits

Fig. A

Always remove the battery before

mounting an accessory.

The drill chuck (7) is suitable for drills and

screwdriver bits with round shaft as well as

hexagonal shaft.

1. Hold the machine firmly with one hand.

Open the drill chuck (7) by rotating the chuck

with your other hand in clockwise direction until

it is opened far enough for the bit to slide in.

3. Insert the shaft of the drill or screwdriver bit.

4. Tighten the drill chuck again by firmly rotating

the chuck (7) counterclockwise.

5. Check if the bit is centered well by shortly

activating the machine´s on/off switch.

Adjusting the gears

Fig. B

Never switch gears when the motor is

running, this will damage your machine.

Never put switch in the middle between

both positions, this will damage your

machine.

The machine has 2 drill speeds, which can be

adjusted by sliding the gear switch (9) forward

or backwards. The number on the gear switch (9)

shows which position is chosen.

• Position 1: For slow drilling, large drilling

diameter or screw driving. The machine has

high power at a low speed.

• Position 2: For fast drilling or small drilling

diameter.

Adjusting the direction of rotation

Fig. A

• Set the direction switch (10) to „“ position in

order to drive screws or to use it for drilling.

• Set the direction switch (10) to „“ position in

order to remove screws.

Switching the machine on and off

Fig. A

The on/off switch (11) is used for activating the

machine and adjusting rotation speed.

• Pressing the on/off switch (11) will activate

the machine, the further the switch is being

pushed, the faster the drill will turn.

• Releasing the on/off switch (11) will stop the

machine.

• Move the direction reversing switch (10) to the

middle position to lock the movement of the

on/off switch.

Only lay down the machine when it has

stopped running completely. Do not

place it on a dusty surface as particles of

dust could get into the mechanism.

Adjusting the torque and activating the impact

(hammer) mode

Fig. B

The machine has 25 different torque settings

and a special drill mode to set the power being

transmitted to the chuck. Next to that, a hammer

mode is available for impact drilling in masonry

and other stone-like materials.

Adjusting the torque setting for Screw driving

By rotating the torque adjustment ring (12),

screws can be driven to a predetermined depth,

which is ideal for repetitive work. The higher the

number, the more torque will be transmitted.

• Select a low setting for small screws or soft

work material.

• Select a high setting for large screws, hard

work materials and when removing screws.

• You should preferably choose a setting as

low as possible when driving screws. Select

a higher setting if the motor slips before the

screw is fully tightened.

Adjusting the torque setting for Drilling

•

For drilling, turn the torque adjustment ring (13)

to the setting for drilling ( ). The motor will

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm CDM1138 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info