Bedienungsanleitung Ferm CDM1138 (Seite 10 von 40) (Englisch, Holländisch)

762253

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

not slip and all power will be available for drilling.

• Make sure the gear switch (9) is set to position

2 to get maximum drill speed.

Adjusting the torque setting for impact drilling

The impact (hammer) function can be used for

drilling in masonry and other stone-like materials.

This function enables faster drilling in masonry

and stone-like materials.

• For impact drilling, turn the torque adjustment

ring (13) to the setting for impact drilling ( ).

The impact function will be activated when

drilling into the material.

• Make sure the gear switch (9) is set to position

2 to get maximum drill speed.



always set to„“ during drilling.

The machine is equipped with electronic

overload protection function. When the

machine gets overloaded it will shut

down automatically. When this happens,

please wait for a few seconds to let the

overload protection reset itself.

Work light (14)

Fig. A

The machine is equipped with a work light to

illuminate the work location.

• It automatically switches on when the on/off

switch (11) is being pressed.

• It automatically switches off when the on/off

switch (11) is released again.

Belt hook (17)

Fig. A

The machine is equipped with a belt hook for

hanging the machine to your belt during use.



middle position to avoid accidental

startup of the machine.

• The belt hook (17) can be assembled on the

left or right side of the machine.

• It can easily be mounted by attaching it with

the screw mounted on the machine.

• It can be removed by simply removing the

screw on the hook and taking it off.

Optimum use

When driving screws into wood, metal and other

materials:

• Before using the appliance check if the drill or

screw bit is properly fitted and centered inside

the drill chuck.

• Screw bits are available in several shapes and

dimensions. When unsure, always try if the bit

fits on the screw head without any free play

before using the machine.

• Make sure the machine is not running when

it contacts the screw. A rotating bit may slip.

This could result in damage to the work piece.

When drilling into wood, metal and other

materials:

• With small diameter drills use a high drill

speed. For large diameter drills use a low drill

speed.

• For hard materials, select a low drill speed, for

soft materials select a high drill speed.

• Fix the work piece properly, preferably by

using a clamp or vice.

• During drilling draw back the drill out of the

hole frequently so swarf or drill dust will be

removed.

When drilling in metal:

• Use a metal drill (HSS). For the best results you

should cool the bit with oil.

• Metal (HSS) drills can also be used drilling into

plastic.

When drilling in stone or masonry:

• Always use drills for concrete or masonry

drilling

• Apply force to the machine to let the hammer

action work at its best, but always make sure

the machine maintains its rotation speed.

Machine will wear out faster, and drilling will

take more time.

• When drilling pull back the drill every few

seconds. Drill dust is being removed out of the

hole and drilling is done faster.

4. MAINTENANCE

Before cleaning and maintenance, always

switch off the machine and remove the

battery pack from the machine.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm CDM1138 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info