Bedienungsanleitung Ferm CRM1039 (Seite 7 von 48) (Deutsch, Englisch, Holländisch, Französisch, Polnisch)

632695

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

Ferm

just make sure that they cannot fall down by

securing them properly. For proper ventilation and

effective cooling, it is important that the

compressor is positioned at least 100 cm from the

wall (fig. 4).

Make sure that the compressor is

transported in the right way, do not turn it

upside down and don’t lift it with hooks or

ropes (fig. 5-6).

Filling the compressor with oil.

Your compressor is supplied with oil which is

already included in the carter.

Before use, remove the transport cap on the carter

(12), and replace it by the regular oil cap (fig 7).

Before use, ensure that oil level is sufficient. This

can be checked by checking the oil inspection

glass (13). When compressor is placed

horizontally, the oil level shall reach the red mark.

Installing the air filters.

Remove the transport lids and replace them with

the supplied air filters before using the

compressor.

Starting up

• Check whether the mains voltage corresponds

to that indicated on the electrical specification

plate (fig. 10), the permitted tolerance range

should be within 5%.

• Press the switch (3) situated on the upper part

into the “0” position according to the pressure

regulator type fitted on the device (fig. 11).

• Put the plug in the plug socket (fig. 9) and start

the compressor up by putting the switch(3) of

the pressure regulator in the “I” position. The

operation of the compressor is fully automatic.

The pressure regulator will stop the

compressor when the maximum value has

been reached and start it up when the

pressure drops below the minimum value.

Normally the difference in pressure is approx.

2 Bar/29 psi between the maximum and the

minimum value. For instance - The

compressor will stop when it reaches 8 Bar

(116 psi) (this is the maximum operating

pressure) and will start up automatically when

the pressure within the tank has dropped to 6

Bar (87 psi).

The head/cylinder/transmission pipe

assembly may reach high temperatures,

so take care when working close to these

parts and do not touch them to avoid

burns (fig. 12 - 13).

Adjusting the operating pressure

Fig. 14

It is not necessary continuously to use the

maximum operating pressure, the compressed-air

tools often require less pressure. With regard to

compressors supplied with a pressure reduction

valve it is necessary to set the operating pressure

properly.

It is possible to set the operating pressure by using

the turning knob(5) on the reduction valve.

• By turning clockwise, the pressure will be

increased.

• By turning anti-clockwise, the pressure will be

reduced.

The compressor has two pressure gauges and

two points to connect an air hose:

• Pressure gauge on the left (7): pressure on left

outlet (6). The pressure of left this outlet can

be regulated with help of the reduction valve

(5).

• Pressure gauge(8) on the right: tank pressure

+ pressure on right outlet(16)

Hints for accurate adjustment of the pressure

regulation:

• Turn the turning knob (5) anti-clockwise till

pressure is fully released

• Connect the air tool you want to use to the left

quick coupler (6)

• Activate the air tool shortly, so the pressure

gauge (7) will show the right pressure level

• Turn the turning knob (5) clockwise, till the

pressure gauge (7) shows the pressure level

you need

• Your air tool is now ready to use.

Note: when not connecting an air tool while

adjusting the pressure, it might occur the pressure

gauge (7) is not reacting accurately on the

pressure drop

4. Maintenance

Make sure that the plug is removed from

the mains when carrying out maintenance

work on the motor.

The machine has been designed to operate over a

long period of time with a minimum of

maintenance. Continuous satisfactory operation

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm CRM1039 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info