Bedienungsanleitung Ferm CRM1039 (Seite 8 von 48) (Deutsch, Englisch, Holländisch, Französisch, Polnisch)

632695

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

8 Ferm

depends upon proper machine care and regular

cleaning. Before interfering in any way whatsoever

with the compressor, please make sure that:

• The switch button is in the “0” position and the

power plug is removed from the power socket

• The air tank is fully decompressed (both

pressure gauges must be pointed at 0 Bar)

Malfunction

Should the machine fail to function correctly, a

number of possible causes and the appropriate

solutions are given below:

Air loss

• May be caused by a poor seal of a connection.

• Check all air connections by wetting them

with a soapy water solution ( Never use

the solution nearby electric connections )

• When the tank is empty and being filled.

The user might hear a sisseling sound by

the pressure switch. This is normal and

will stop before the compressor reach a

pressure of 1.5 bar

• Check if the drain valve ( 14 ) is closed

well

The compressor will not start

• If the compressor is difficult to start, check:

• whether the voltage of the mains

corresponds to that on the specification

plate (fig. 10)

• whether electrical extension cables are

being used with a faulty core or length.

• whether the operating environment is too

cold (below 0°C).

• whether there is electricity supply (plug

properly connected, magneto-thermal

fuses not broken).

The compressor does not shut off

If the compressor does not shut off when the

maximum pressure has been reached, the safety

valve of the tank will be activated. It is necessary

to contact the nearest authorised Support Service

for the repair.

Repairs and servicing should only be

carried out by a qualified technician or

service firm.

Cleaning

Regularly clean the machine housing with a soft

cloth, preferably after each use. Keep the

ventilation slots free from dust and dirt.

If the dirt does not come off use a soft cloth

moistened with soapy water. Never use solvents

such as petrol, alcohol, ammonia water, etc.

These solvents may damage the plastic parts.

Drain the tank

Compressing air will cause water in the tank.

Regularly drain the water from the tank to prevent

tank corrosion (fig 16):

• First reduce the pressure in the tank till

aprroxially 2 bar by connecting and activating

an air tool .

• Then slowly turn the drain valve (14) on the

lower side of the tank open.

• The water in the tank will now leak out of the

tank

Take care when compressed air is in the tank

because the water can come out with some force.

Recommended pressure max. 1-2 Bar.

Clean the air filter

It is recommended to disassemble the suction filter

every 50 operating hours and to clean the filter

element by blowing it with compressed air (fig. 15).

It is recommended that the filter element is

replaced at least once a year if the compressor is

working in a clean environment; more often if the

environment in which the compressor is situated is

dusty.

Replacing/topping up oil

The compressor has been supplied with synthetic

oil “SAE 10W30”. It is recommend to fully

replace the oil of the pump system within the first

100 operating hours.

• Unscrew the drain plug (gauge) (13) on the

sump lid, let all the oil run out and screw back

the

plug (fig. 17).

• Filltheoilviatheupperholeofthesumplid

(fig.18) until the level indicated on the gauge

(13)

(fig. 8) has been reached.

Check the oil level of the pump system

every week and if necessary top up.

The synthetic oil has the advantage that it

does not lose its characteristics, either in

summer or in winter periods.

For replacement of oil the table below should be

adhered to.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm CRM1039 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info