Bedienungsanleitung Ferm CSM1037 (Seite 7 von 72) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

763369

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

Ferm

vibrate, causing the blade to break more

easily.

Let the saw do the job. Do not put undue

pressure on the circular saw.

5. MAINTENANCE

Make sure that the machine is not live

when carrying out maintenance work on

the motor.

The machines have been designed to operate

over a long period of time with a minimum of

maintenance. Continuous satisfactory operation

depends upon proper machine care and regular

cleaning.

Troubleshooting

Below we have listed a few probable causes and

solutions to which you can refer if your circular

saw does not function properly.

1. The temperature of the electric motor ex-

ceeds 70°C.

• The motor has been overloaded by working it

too hard.

• Cut more slowly and allow the motor to

cool down.

• The motor is defective.

• Please contact the service address on

the warranty card.

2. The tool does not work when switched on.

• Damaged cord and/or plug.

• Check cord and/or plug.

• Defective switch.

• Please contact the service address on

the warranty card.

3. When cutting it is very difficult to move the

work forward in a straight line and the cut

is not clean.

• The blade is bent or blunt.

• Replace the blade.

4. The circular saw makes a lot of noise and/

or does not run smoothly.

• The carbon brushes are worn.

• Please contact the service address on

the warranty card.

Cleaning

Keep the ventilation slots of the machine clean to

prevent overheating of the engine.

Regularly clean the machine housing with a

soft cloth, preferably after each use. Keep the

ventilation slots free from dust and dirt.

If the dirt does not come off use a soft cloth

moistened with soapy water. Never use solvents

such as petrol, alcohol, ammonia water, etc.

These solvents may damage the plastic parts.

Replacing hte carbon brushes

• Remove the screws (17).

• Withdraw the carbon brushes (18) from the

circular handsaw and inspect them for wear.

• Place the carbon brushes back in the brush

holders provided.

• Check that the copper contact on the carbon

brushes makes good contact with the copper

part in the brush holder.

• Replace the screws (17) and tighten them

firmly.

Frequent use will cause the carbon

brushes to wear down. Regular

inspection, after every 30 hours of use,

is essential. If the brushes have worn

down to less than 4 mm, replace.

Lubrication

The machine requires no additional lubrication.

Faults

Should a fault occur, e.g. after wear of a part,

please contact the service address on the

warranty card. In the back of this manual you find

an exploded view showing the parts that can be

ordered.

Environment

To prevent damage during transport, the

appliance is delivered in a solid packaging which

consists largely of reusable material. Therefore

please make use of options for recycling the

packaging.

Faulty and/or discarded electrical or

electronic apparatus have to be

collected at the appropriate recycling

locations.

Warranty

The warranty conditions can be found on the

separately enclosed warranty card.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm CSM1037 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info