Bedienungsanleitung Ferm CSM1043 (Seite 7 von 140) (Alle Sprachen)

762265

Zoom out

Zoom in

Vorherige Seite

1/140

Nächste Seite

a cut for any reason, release the trigger and

hold the saw motionless in the material until

the blade comes to a complete stop. Never

attempt to remove the saw from the work or

pull the saw backward while the blade is in

motion or kickback may occur. Investigate and

take corrective actions to eliminate the cause

of blade binding.

c) When restarting a saw in the workpiece, centre

the saw blade in the kerf and check that saw

teeth are not engaged into the material. If saw

blade is binding, it may walk up or kickback

from the workpiece as the saw is restarted.

d) Support large panels to minimise the risk of

blade pinching and kickback. Large panels tend

to sag under their own weight. Supports must

be placed under the panel on both sides, near

the line of cut and near the edge of the panel.

e) Do not use dull or damaged blades.

Unsharpened or improperly set blades

produce narrow kerf causing excessive

friction, blade binding and kickback.

f) Blade depth and bevel adjusting locking levers

must be tight and secure before making cut.

If blade adjustment shifts while cutting, it may

cause binding and kickback.

g) Use extra caution when making a “plunge

cut” into existing walls or other blind areas.

The protruding blade may cut objects that can

cause kickback.

Safety instructions guard

a) Check guard for proper closing before each

use. Do not operate the saw if guard does not

move freely and enclose the blade instantly.

Never clamp or tie the guard with the blade

exposed. If saw is accidentally dropped, guard

may be bent. Check to make sure that guard

moves freely and does not touch the blade or

any other part, in all angles and depths of cut.

b) Check the operation and condition of the

guard return spring. If the guard and the

spring are not operating properly, they must

be serviced before use. Guard may operate

sluggishly due to damaged parts, gummy

deposits, or a build-up of debris.

c) Assure that the guide plate of the saw will not

shift while performing the “plunge cut” when

the blade bevel setting is not at 90°. Blade

shifting sideways will cause binding and likely

kick back.

d) Always observe that the guard is covering the

blade before placing saw down on bench or

floor. An unprotected, coasting blade will cause

the saw to walk backwards, cutting whatever is

in its path. Be aware of the time it takes for the

blade to stop after switch is released.

Specific safety instructions

• Do not use misshaped or cracked blades.

• Regularly check the blades for damage. If

necessary, replace them.

• Only use blades recommended by Ferm.

• Never use a saw that has components missing

or a saw that is fitted with accessories which

were not supplied with the saw or which are not

recommended for use with the saw.

• Never exert sideways pressure on the blade to

bring it to a stop.

• Remove the plug from the plug socket before

checking whether the protective cover can

move freely and does not become stuck.

• Do not lock or clamp the protective cover.

• Do not use the saw without the protective cover.

• Before using the saw, check whether the

protective cover has been fitted.

• Always remove the plug from the plug socket

before removing the protective cover, replacing

the blade or when checking the saw and

carrying out maintenance work.

• A damaged power cord should only be replaced

by the manufacturer or a service agent.

• After use, the saw must be stored in such a way

that the blade cannot become damaged.

• Do not use abbrasive discs .

• Always wear a dust mask

• Only use saw blades recommended (e.g saw

blades intended for wood shall have EN 847-1

approval)

• Always wear hearing protection

• Only use blade diameter in accordance with the

marking label

• Have a suitable, tested vacuum removal device

attached to the saw when working with woods

or materials that create dusts that may be

hazardous to health.

• When cutting plastics, avoid to overheat the

blade, avoid to melt the plastic!

• Be careful when handling the saw blades

as they are sharp and can cause injury. It is

recommended to wear protective gloves when

handling the saw blades.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm CSM1043 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info