Bedienungsanleitung Ferm fag 125 1050 (Seite 7 von 84) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

391290

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

Ferm

cut while the wheel is in motion otherwise

kickback may occur. Investigate and take

corrective action to eliminate the cause of

wheel binding.

d) Do not restart the cutting operation in the

workpiece. Let the wheel reach full speed

and carefully reenter the cut. The wheel may

bind, walk up or kickback if the power tool is

restarted in the workpiece.

e) Support panels or any oversized workpiece

to minimize the risk of wheel pinching and

kickback. Large workpieces tend to sag under

their own weight. Supports must be placed

under the workpiece near the line of cut and

near the edge of the workpiece on both sides

of the wheel.

f) Use extra caution when making a “pocket cut”

into existing walls or other blind areas. The

protruding wheel may cut gas or water pipes,

electrical wiring or objects that can cause

kickback.

Special safety instructions

Check that the maximum speed indicated on •

the grinding disc corresponds to the maximum

speed of the machine.

The speed of the machine must not exceed

the value on the grinding disc.

Make sure that the dimensions of the grinding •

disc correspond to the specifications of the

machine.

Make sure that the grinding disc has been •

mounted and fastened properly. Do not use

reducing rings or adapters to make the

grinding disc fit properly.

Treat and store grinding discs in conformance •

with the supplier’s instructions.

Do not use the machine for grinding •

workpieces with a maximum thickness

exceeding the maximum grinding depth of the

grinding disc.

Do not use grinding discs for deburring.•

When grinding discs have to be mounted on •

the thread of the spindle, make sure that the

spindle has sufficient thread. Make sure that

the spindle is sufficiently protected and does

not touch the grinding surface.

Before use, inspect the grinding disc for any •

damage. Do not use grinding discs which are

cracked, ripped or otherwise damaged.

Before use, let the machine run idle for 30 •

seconds. Immediately switch off the machine

in case of abnormal vibrations or occurrence

of another defect. Carefully inspect the

machine and grinding disc before switching

the machine on again.

Make sure that sparks do not put people into •

danger or that they contact highly flammable

substances.

Make sure that the workpiece is sufficiently •

supported or clamped. Keep your hands away

from the surface to be cut.

Always wear safety goggles and hearing •

protection. If desired or required also use

another kind of protection like for example an

apron or helmet.

Ensure that mounted wheels and points are •

fitted in accordance with the manufacturer’s

instructions.

Ensure that blotters are used when they are •

provided with the bonded abrasive product

and when they are required.

If a guard is supplied with the tool never use •

the tool without such a guard.

For tools intended to be fitted with threaded •

hole wheel, ensure that the thread in the

wheel is long enough to accept the spindle

length.

Ensure that ventilation openings are kept •

clear when working in dusty conditions. If it

should become nessesary to clear dust, first

disconnect the tool from the mains supply

(use non metallic objects) and avoid

damaging internal parts.

Though poor conditions of the electrical •

mains, shortly voltage drops can appear when

starting the equipment. This can influence

other equipment (eq. blinking of a lamp). If the

mains-impedance Zmax <0.348 Ohm, such

disturbances are not expected. (In case of

need, you may contact your local supply

authority for further information.

Immediately switch off the machine when:

Excessive sparking of the carbon brushes and •

verticiliosis in the collector.

Interruption of the mains plug, mains lead or •

mains lead damage.

Defect switch•

Smoke or stench of scorched isolation•

Electrical safety

When using electric machines always observe the

safety regulations applicable in your country to

reduce the risk of fire, electric shock and personal

injury. Read the following safety instructions and

also the enclosed safety instructions.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm fag 125 1050 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info