Bedienungsanleitung Ferm fag 125 1050 (Seite 8 von 84) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

391290

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

Ferm

Always check that the power supply

corresponds to the voltage on the rating

plate.

Class II machine – Double insulation –

You don’t need any earthed plug.

Replacing cables or plugs

Immediately throw away old cables or plugs

when they have been replaced by new ones. It is

dangerous to insert the plug of a loose cable in

the wall outlet.

Using extension cables

Only use an approved extension cable suitable

for the power input of the machine. The minimum

conductor size is 1,5 mm

. When using a cable

reel always unwind the reel completely.

3. ASSEMBLY

Prior to mounting an accessory always

unplug the tool.

Assembling the hand grip

Fig. 1

The hand grip is suitable for either left or right-

handed use.

Turn the hand grip (3) to the notch on the right •

side of the machine for left-handed use.

Turn the hand grip (3) to the notch on the left •

side of the machine for right-handed use.

Turn the hand grip to the notch on the top of •

the machine to use it vertically.

Mounting a grinding disc

Fig. 2

Use grinding discs of the correct dimension. Use

fibre reinforced grinding discs only.

The grinding disc must not touch the edge of the

guard.

Press the spindle lock (6) and turn the spindle •

(9) until it engages in the lock. Keep the

spindle lock pressed during this procedure.

Remove the flange nut (12) from the spindle •

using the spanner (11).

Position the grinding disc (7) on the flange (5).•

Place the flange nut on the spindle an tighten •

it using the spanner.

Release the spindle lock and check that the •

spindle is unlocked by rotating it.

Mounting grinding discs and roughing discs

Fig. 3 and 4 show how to mount the flange (10)

when using thick (4 - 8 mm) and thin

(2,5 - 4 mm) discs.

The following grinding discs can be used with this

grinder.

For deburring: grooved, fibreglass reinforced •

type 27. Dimensions Ø 125x6.0x22.2 mm.

For slitting/ cutting: grooved, fibreglass •

reinforced, type 41 and type 42. Dimensions

Ø 125x3.0x22.2 mm.

If you use normal grinding discs they

should always be fibreglass reinforced.

4. USE

Always follow the safety instructions

and keep to the applicable regulations.

Hold the machine away from the workpiece when

turning it on and off because the grinding disc

could damage the workpiece.

Clamp the workpiece firmly or use another •

method to ensure that it cannot move while

working.

Check the discs regularly. Worn grinding discs •

have a negative effect on the machine’s

efficiency. Change to a new grinding disc in

good time.

Always first turn the machine off after use •

before removing the plug from the socket.

Deburring

Fig. 5

An angle of inclination of 30º to 40º will give the

best results when deburring. Move the machine

back and forth using light pressure. This will

prevent the workpiece from discolouring or

becoming too hot and will avoid making groves.

Never use abrasive cutting discs for

deburring work!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm fag 125 1050 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info