Bedienungsanleitung Ferm FDPD 710 (Seite 6 von 104) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

78861

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

ASSEMBLY

Before assembly, always switch off the

machine and remove the mains plug

from the mains.



The machine is suitable for use of the following

drill bits:

- Wood (HSS)

- Metal (HSS)

- Concrete / masonry (hard metal)

Mounting

● Open the chuck (6) by turning the collar (11)

counterclockwise.

● Insert the drill bit (12) into the chuck (6).

● Close the chuck (6) by turning the collar (11)

clockwise.

Removing

● Open the chuck (6) by turning the collar (11)

counterclockwise.

● Remove the drill bit (12) from the chuck (6).

● Close the chuck (6) by turning the collar (11)

clockwise.



Mounting

● Loosen the auxiliary grip (8).

● Slide the auxiliary grip (8) over the chuck (6).

● Turn the auxiliary grip (8) to the required

position.

● Tighten the auxiliary grip (8).

Removing

● Loosen the auxiliary grip (8).

● Remove the auxiliary grip (8) from the chuck (6).

● Tighten the auxiliary grip (8).



The depth stop is used to set the maximum

drilling depth.

Mounting

● Loosen the auxiliary grip (8).

● Insert the depth stop (9) through the hole in

the auxiliary grip (8).

● Set the depth stop (9) to the required position.

● Tighten the auxiliary grip (8).

Removing

● Loosen the auxiliary grip (8).

● Remove the depth stop (9) from the auxiliary

grip (8).

● Tighten the auxiliary grip (8).

USE



● To switch on the machine, press the on/off

switch (1). The further the on/off switch (1) is

pressed, the higher the speed of the machine.

● To switch the machine to continuous mode,

keep the on/off switch (1) pressed and

simultaneously press the lock-on button (2).

● To switch off continuous mode, press the

on/off switch (1) again.

● To switch off the machine, release the on/off

switch (1).



Do not change the direction of rotation

during use.

● For clockwise rotation, slide the forward/

reverse switch (4) to the left.

● For counterclockwise rotation, slide the

forward/reverse switch (4) to the right.



Do not set the speed during use.

● Turn the speed adjustment wheel (3) clockwise

to increase the maximum drilling speed.

● Turn the speed adjustment wheel (3)

counterclockwise to decrease the maximum

drilling speed.



Do not change the operating mode

during use.

● Set the switch (5) to position „A“ for drilling.

● Set the switch (5) to position „B“ for hammer

drilling.

Hints for optimum use

● Clamp the workpiece.

● Firmly hold the machine with both hands.

● Place the drill bit on the workpiece.

● Switch on the machine.

● Do not apply too much pressure on the

machine. Let the machine do the work.

● Switch off the machine and wait for the

machine to come to a complete standstill

before putting the machine down.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm FDPD 710 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info