Bedienungsanleitung Ferm FKS 185 L (Seite 7 von 56) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Norwegisch)

110130

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

Ferm 07

Danger

a) Keep hands away from cutting area and the blade. Keep your second hand on auxiliary

handle, or motor housing. If both hands are holding the saw

, they cannot be cut by the blade.

b) Do not reach underneath the workpiece. The guard cannot protect you from the blade

below the workpiece.

c) Adjust the cutting depth to the thickness of the workpiece. Less than a full tooth of the blade

teeth should be visible below the workpiece.

d) Never hold piece being cut in your hands or across your leg. Secure the workpiece to a

stable platform. It is important to support the work properly to minimize body exposure,

blade binding, or loss of control.

e) Hold power tool by insulated gripping surfaces when performing an operation where the

cutting tool may contact hidden wiring or its own cord. Contact with a "live" wire will also

make exposed metal parts of the power tool "live" and shock the operator.

f) When ripping always use a rip fence or straight edge guide. This improves the accuracy of

cut and reduces the chance of blade binding.

g) Always use blades with correct size and shape (diamond versus round) of arbour holes.

Blades that do not match the mounting hardware of the saw will run eccentrically, causing

loss of control.

h) Never use damaged or incorrect blade washers or bolt. The blade washers and bolt were

specially designed for your saw, for optimum performance and safety of operation.

Causes and operator prevention of kickback

• Kickback is a sudden reaction to a pinched, bound or misaligned saw blade, causing an

uncontrolled saw to lift up and out of the workpiece toward the operator;

• When the blade is pinched or bound tightly by the kerf closing down, the blade stalls and

the motor reaction drives the unit rapidly back toward the operator;

•

If the blade becomes twisted or misaligned in the cut, the teeth at the back edge of the blade

can dig into the top surface of the wood causing the blade to climb out of the kerf and jump

back toward the operator.

Kickback is the result of saw misuse and/or incorrect operating procedures or conditions and

can be avoided by taking proper precautions as given below.

a) Maintain a firm grip with both hands on the saw and position your arms to resist kickback

forces. Position your body to either side of the blade, but not in line with the blade. Kickback

could cause the saw to jump backwards, but kickback forces can be controlled by the

operator,if proper precautions are taken.

b) When blade is binding, or when interrupting a cut for any reason, release the trigger and

hold the saw motionless in the material until the blade comes to a complete stop. Never

attempt to remove the saw from the work or pull the saw backward while the blade is in

motion or kickback may occur. Investigate and take corrective actions to eliminate the

cause of blade binding.

c) When restarting a saw in the workpiece, centre the saw blade in the kerf and check that

saw teeth are not engaged into the material. If saw blade is binding, it may walk up or

kickback from the workpiece as the saw is restarted.

d) Support large panels to minimise the risk of blade pinching and kickback. Large panels

tend to sag under their own weight. Supports must be placed under the panel on both

sides, near the line of cut and near the edge of the panel.

106 Ferm

Rengøring

Rengør regelmæssigt maskinkappen med en blød klud, helst efter hvert brug. Sørg for at

ventilationshullerne er fri for støv og snavs. Brug en blød klud, der er vædet i sæbevand til

at fjerne hårdnakket snavs. Brug ingen opløsningsmidler, så som benzin, alkohol, ammo-

niak, osv

. Den slags stoffer beskadiger kunststofdelene.

Udskiftning af kulbørster

Fig. E

• Fjern skruerne (1).

•

Træk kulbørsterne (2) ud fra rundsaven og undersøg dem for slitage.

• Sæt kulbørsterne tilbage i de forhåndenværende holdere.

• Kontroller, at kobberkontakten på kulbørsterne er i god kontakt med kobberdelen i

børsteholderen.

• Sæt skruerne (1) i igen og stram dem godt.

Efter mange driftstimer kan kulbørsterne være slidt. Derfor skal kulbørsterne

kontrolleres regelmæssigt efter hver 30 driftstimer

. Hvis kulbørsterne er kortere

end 4 mm, skal de udskiftes med nye.

Smøring

Maskinen behøver ingen ekstra smøring.

• Elektromotoren over-

ophedes.

• Maskinen virker ikke,

selv om den er tilko-

blet.

• Det er vanskeligt at

føre arbejdsemnet i en

ret linie langs savklin-

gen og savskæret er

uregelmæssigt.

• Rundsaven støjer

og/eller går meget ure-

gelmæssigt.

• Motoren overbelastes,

fordi der saves for

store arbejdsemner.

• Motoren er defekt.

• Fejl i netledningen.

• Afbryderen er defekt.

• Savklingen er bøjet

eller sløv.

• Kulbørsterne er slidte.

• Sav i et lavere tempo

og lad motoren køle af.

• Kontakt venligst serv-

iceadressen på garanti-

beviset.

• Kontrollér netledningen

for brud.

• Kontakt venligst serv-

iceadressen på garanti-

beviset.

• Udskift savklingen.

• Kontakt venligst serv-

iceadressen på garanti-

beviset.

Ferm FKS 185 L Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Ferm FKS 185 L

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info