Bedienungsanleitung Ferm FKS 185 L (Seite 8 von 56) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Norwegisch)

110130

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

Ferm 105

Tilkobling/Frakobling

Fig. E

• T

ryk på knappen (B) med højre hånds tommelfinger og hold knappen trykt ned.

• Tryk derefter på knappen (A). Rundsaven starter nu.

• Rundsaven stopper, når du slipper knappen (A).

Ibrugtagning

• Klem arbejdsemnet fast, således at begge hænderne er fri til at fastholde og betjene

rundsaven.

•

Tilkobl rundsaven og placér savebunden på arbejdsemnet.

• Tryk forsigtigt på rundsaven og bevæg den langsomt frem langs den på forhånd teg-

nede skærelinie.

• Tryk savebunden fast mod arbejdsemnet.

Lad rundsaven gøre arbejdet! Undlad derfor at udøve for meget tryk på rund-

saven.

5. VEDLIGEHOLDELSE

Sørg for at maskinen ikke står under strøm, når der udføres vedligeholdelse-

sarbejder på mekanikken.

Maskinerne er udviklet til at fungere længe uden problemer med et minimum af vedlige-

holdelse. V

ed at rengøre maskinen regelmæssigt og behandle den korrekt, bidrager De til

en længere levetid for maskinen.

Fejl

Hvis rundsaven ikke virker hensigtsmæssigt, kan du gennemgå følgende mulige årsager

og tilhørende løsninger for at afhjælpe problemerne.

• Elektromotoren over-

ophedes.

• Maskinen virker ikke,

selv om den er tilko-

blet.

• Motoren overbelastes,

fordi der saves for

store arbejdsemner.

• Motoren er defekt.

• Fejl i netledningen.

• Afbryderen er defekt.

• Sav i et lavere tempo

og lad motoren køle af.

• Kontakt venligst serv-

iceadressen på garanti-

beviset.

• Kontrollér netledningen

for brud.

• Kontakt venligst serv-

iceadressen på garanti-

beviset.

08 Ferm

e) Do not use dull or damaged blades. Unsharpened or improperly set blades produce

narrow kerf causing excessive friction, blade binding and kickback.

f) Blade depth and bevel adjusting locking levers must be tight and secure before making cut.

If blade adjustment shifts while cutting, it may cause binding and kickback.

g) Use extra caution when making a "plunge cut" into existing walls or other blind areas. The

protruding blade may cut objects that can cause kickback.

Safety instructions lower guard

a) Check lower guard for proper closing before each use. Do not operate the saw if lower

guard does not move freely and close instantly

. Never clamp or tie the lower guard into the

open position. If saw is accidentally dropped, lower guard may be bent. Raise the lower

guard with the retracting handle and make sure it moves freely and does not touch the

blade or any other part, in all angles and depths of cut.

b) Check the operation of the lower guard spring. If the guard and the spring are not operating

properly, they must be serviced before use. Lower guard may operate sluggishly due to

damaged parts, gummy deposits, or a build-up of debris.

c) Lower guard should be retracted manually only for special cuts such as "plunge cuts" and

"compound cuts." Raise lower guard by retracting handle and as soon as blade enters the

material, the lower guard must be released. For all other sawing, the lower guard should

operate automatically.

d) Always observe that the lower guard is covering the blade before placing saw down on

bench or floor.An unprotected, coasting blade will cause the saw to walk backwards,

cutting whatever is in its path. Be aware of the time it takes for the blade to stop after switch

is released.

Before using the circular saw

• Check the following points:

• Does the voltage of the motor correspond with the mains voltage (appliances for a

mains voltage of 230 V

•

Are the mains lead and the mains plug in a good condition: solid, without any loose

ends or damage;

• Is the saw blade missing any teeth or showing any cracks, it so must be replaced

immediately.

• Make sure the blade is secure.

• Use this circular saw to saw only wood, wood-like products.

• Do not use circular saw blades wich are deformed or damaged.

•

Do not use HSS blades.

• Only use blades meeting the required dimensions, as well as data and descriptions;

Never apply any blades of which the thickness is greater than that of the riving knife.

• Do not stop the blade of a circular saw by pressing the blade from the side.

• Check that the blade guard can freely move and fully closes.

• Never lock-up the guard in the open position.

• Never put sideward pressure on the blade. This may cause the blade to break.

• Be careful when cutting wood with knots, nails or cracks in it and/or dirt on it, as these can

cause the blade to get stuck.

• Never leave the circular saw unattended.

• Use this circular saw to saw only wood or wood-like products.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm FKS 185 L Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Ferm FKS 185 L

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info