Bedienungsanleitung Ferm FKZ-255RL (Seite 10 von 80) (Deutsch, Englisch, Holländisch, Französisch, Spanisch)

462374

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

anchored to the floor or to a floor plate with

dimensions of at least 1 square meter.

Guide fence insert

For safety reasons, this machine is equipped with

a guide fence insert

to be used when using the machine for sawing

straight cross-cuts.

For sawing straight cross-cuts, the guide •

fence insert must remain mounted on the

machine (fig. 6).

For sawing mitre cuts, the guide fence insert •

must be removed from the machine as shown

(fig. 6).

For sawing bevel cuts, the guide fence insert •

must be removed from the machine as shown

(fig. 7+8).

Changing the saw blades

Fig. 4

Only use saw blades that are sharp and

undamaged. You must immediately

replace chipped or bent saw blades.

Make sure that the plug is not in the socket!•

Lock the head of the machine in its highest •

position.

Unscrew the screw (20) by one turn •

(anticlockwise).

Move the hood (6) forwards. Push the saw •

blade interlock (22) in and unscrew the bolt

(18) with the key supplied (clockwise).

Remove the saw blade flange (19) and •

change the blade. Make sure that the blade is

mounted in the machine correctly: with the

arrow on the blade pointing clockwise.

Replace the flange (19) and push the interlock •

(22) in and screw the bolt (18) tight again.

Move the hood (6) back and screw the screw •

(20) tight again (clockwise).

Adjusting the saw angle

Fig. 3

The mitring angle is 45º, both left and right.

Unscrew the knob (9) a half turn clockwise.•

Turn the machine to the desired angle (the •

angle can be read off on the front of the

machine).

Screw up the knob (9) a half turn •

anticlockwise.

The turntable clicks into place at the following •

angles: 0º, 15º, 22.5º, 30º and 45º (both left

and right).

Setting up the double sawing angle / mitring

Fig. 2

Adjust the first angle as described for •

adjusting the saw angle (above).

Turn the knob (12) anticlockwise and then set •

the angle desired (you can read this off on the

back of the machine. Then tighten the knob

(12) again by turning it clockwise.

Changing the carbon brushes

Fig. 1

Make sure that the plug is not in the socket!•

Unscrew the covers (4) with a flat bladed •

screwdriver. Remove the carbon brushes with

the same type of brushes. Screw the covers

(4) tight again.

Note: Always replace both carbon brushes at the

same time. Never use a mixture of old and new

brushes.

Mounting the dust bag

Fig. 2

Press in the clamp of the dust bag (13) and slide

it onto the opening on the back of the machine.

The dust bag stays in place when you release the

clamp.

4. Operation

Using the mitre saw

Fig. 1

Before use, always check for faults or

defects!

Set the desired sawing angle of the machine.•

Put the plug into the socket.•

Fix the piece of work in place using the •

clamps (7): make sure that the material is well

clamped in place!

Hold the material tightly on the left side while •

making sure that you keep a safe distance

from the blade of the saw.

Turn on the machine using the switch (1).•

Make sure that the saw blade has reached full •

speed before allowing it to touch the piece of

work to be sawn.

Use knob (3) to raise the protective cover •

lock.

Now bring the saw slowly downwards so that •

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm FKZ-255RL Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info