Bedienungsanleitung Ferm FKZ-255RL (Seite 11 von 80) (Deutsch, Englisch, Holländisch, Französisch, Spanisch)

462374

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

the saw blade saws through the piece of work

and passes through the slot in the table. Do

not put any pressure on the saw. Give the

machine time to saw through the piece of

work.

Bring the machine gently up again and switch •

it off by letting go of the switch (1).

Using the slide-function

Fig. 1

The machine must be firmly bolted to a

workbench.

Use the slide-function for sawing wide

workpieces:

Fix the piece of work in place using the clamp•

Screw up the knob (10) a half turn •

anticlockwise.

Slide the machine completely towards •

yourself

Turn on the machine using the switch•

Bring the saw slowly downwards so the saw •

blade saws through the piece of work

Push the machine slowly backwards (in •

direction of guide fence)

Bring the machine gently up again and switch •

it off by letting go of the switch

Using the laser

Fig. 2

To switch on the laser , press the on/off switch •

To switch off the laser , release the •

on/off switch 2.

5. Service and maintenance

Always make sure that the machine is

not connected to the mains electricity

when you carry out any maintenance of

the mechanism.

Slide rails

Dirt can damage the slide rails and thereupon the

operating of the machine.

Clean the slide rails regularly with a soft cloth.•

Drip some lubricating oil on the slide rails•

Move the mitre saw forwards and backwards •

so the oil spreads over the complete rails

These machines are designed to function for a

long time without any problems with a minimum of

maintenance. By cleaning the machine regularly

and using it in the correct way you can contribute

to a long life of your machine.

Cleaning

Clean the machine housing regularly with a soft

cloth, preferably after each time you use the

machine. Make sure that the ventilation slots are

free of dust and dirt. For stubborn dirt use a soft

cloth dampened with soapy water. Never use

solvents such as benzene, alcohol, ammonia, etc.

These types of solvents can damage the plastic

parts.

Problem solving

1. The motor does not start

The plug is not in the socket•

The power cord is broken•

The switch is defective. Take the machine to •

your dealer for repair.

2. The saw cut is not even (jagged)

The saw blade must be sharpened•

The saw blade is mounted back to front•

The saw blade is clogged with resin or •

sawdust

The saw blade is not suitable for the piece of •

work being used

3. The height and/or mitre lever is obstructed

Chips and/or dust must be removed•

4. The motor has difficulty in reaching full

speed

The extension cord is too thin and/or too long•

The mains voltage is less than 230 V•

5. The machine vibrates excessively

The saw blade is damaged•

6. The machine becomes excessively hot

The ventilation slots are blocked. Clean them •

out with a dry cloth.

7. The electromotor runs unevenly

The carbon brushes are worn out. Replace •

the carbon brushes or consult your dealer.

Lubrication

The machine does not need any extra lubrication.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm FKZ-255RL Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info