Bedienungsanleitung Ferm FPJS 1800 LK (Seite 7 von 60) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

110287

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

Ferm

Special safety instructions

Read the following safety instructions and also the

enclosed safety instructions.

Before using the appliance

Check the following points:

Has the saw blade lost any teeth and is it •

showing cracks or fractures?

If so, replace the saw blade immediately.•

Is there enough room under the workpiece so •

that the saw blade does not come into contact

with the floor or work table as it moves up and

down?

Do the teeth of the saw blade point upwards?•

Always wear protective goggles when using •

the appliance.

Maintain the appliance carefully.•

Do not use the appliance in a wet •

environment.

Do not use the appliance for material which •

contains asbestos.

Never leave the jig saw unattended.•

Using the appliance

Clamp the workpiece that you will be sawing in •

firmly into place.

Remove any wood residue that is near or •

stuck to the surface of the saw blade; do not

use your hand for this. Switch the appliance off

before removing any residue!

Always switch the jig saw on in idle, i.e. switch •

the jig saw on before bringing it into contact

with the workpiece.

When sawing the wood watch out for knots, •

nails, cracks and/or dirt deposits. These can

cause the saw blade to jam dangerously. Also

watch out for this with waste wood. This often

requires less careful sawing, so there is a

danger that you may not be quite so careful

about watching out for irregularities in the

wood.

Do not saw workpieces that are thicker than •

the length of the saw blade.

Do not touch metal parts of the jig saw when •

sawing in walls or floors in which there could

be electricity cables. Hold the jig saw tightly

with both hands on the plastic grip so that you

do not touch parts that could become live if

you accidentally saw through an electricity

cable.

When you have finished sawing, switch off the •

appliance first and wait until the saw blade

comes to a standstill before removing it from

the workpiece.

Keep the plastic guard in place while the jig •

saw is in use.

3. MOUNTING ACCESSORIES

Prior to mounting an accessory always

remove the battery.

Selecting the saw blade

The jig saw is suitable for all commercially

available T-shank saw blades. The profile and the

teeth vary is according to the material that you

want to saw. A fine tooth will give you a smooth

and precise saw cut. Use a narrow profile if you

want to saw curves or if you are going to saw

figures.

The maximum saw capacity in wood is 70 mm.

To select the right saw, proceed as follows:

First of all try a saw blade with coarse teeth.•

If you don‘t get a smooth and precise saw cut, •

try a saw blade with a finer tooth.

For plastic, aluminium and steel always use a •

saw blade with a very fine tooth.

For metal, only use saw blades, suitable for •

metal.

In general you will work faster but less precisely

with a coarse tooth than with a fine tooth.

For an optimum result always make sure the saw

blade is sharp.

Saw blade Type of workpiece

Coarse Wood

Medium Wood

Fine Plastic, aluminium, steel

Very fine Cutting curves (wood)

Assembling saw blade

Fig. B

To assemble the saw, proceed as follows:

Push the saw buckle clamp up and hold.•

Place the saw in the saw buckle. Make sure •

that the teeth point upwards and forward. The

smooth side of the saw must rest against the

wheel.

Push the saw as far into the buckle as •

possible.

Secure the saw by gently releasing the saw •

buckle clamp. Make sure that the saw blade

sits correctly in the saw buckle. A crooked

blade can result in an unsatisfactory cut.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm FPJS 1800 LK Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info