Bedienungsanleitung Ferm FRS-710 (Seite 4 von 52) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Norwegisch)

110232

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

Ferm4

• Alwaysremovetheplugfromthemains

socket before carrying out any work on the

machine.

• Donotcarrythemachinebythecable.

• Incorrecthandlingmaydamagethe

machine. Therefore always comply with the

following instructions.

• Useonlysharpsawbladesinperfect

condition; replace cracked, distorted or

blunt saw blades immediately.

• Machineshouldonlybeswitchedonwith

blade installed

• Selecttools,strokerateandpendulum

actions according to material, Take care to

maintain a constant reed rate.

• Donotattempttostopthesawbladewith

lateral pressure after switching off.

• Onlyusegenuineaccessories.

• Alwaysusethecorrectsupplyvoltage.The

voltage specifications on the rating plate

must correspond with the mains voltage.

Equipmentmarkedwith230Vcanalsobe

connected to 220-240 V.

IMMEDIATELY SWITCH OFF THE MACHINE

WHEN:

• Excessivesparkingofthecarbonbrushes

and verticiliosis in the collector.

• Interruptioninthemainsplug,mainsleador

mains lead damage.

• Defectswitch.

• Smokeorstenchofscorchedinsulation.

ELECTRICAL SAFETY

Always check that the power supply

corresponds to the voltage on the

rating plate.

Your machine is double insulated in

accordance with EN 50144; therefore

no earthwire is required.

Replacing cables or plugs

Immediatelythrowawayoldcablesorplugs

whentheyhavebeenreplacedbynewones.It

is dangerous to insert the plug of a loose cable

in the wall outlet.

Using extension cables

Onlyuseanapprovedextensioncablesuitable

for the power input of the machine. The

minimum conductor size is 1.5 mm

When using a cable reel always unwind the reel

completely.

OPERATION

CHANGING/FITTING THE BLADE

Fig.B

Ensure the machine is unplugged.

• Loosenthegrubscrewwiththe3mm

hexagon key.

• Insertthesawbladebetweenthestrokerod

and the clamping plate.

• Takecarethatthesecuringpinofthe

stroke rod engages in the hole of the saw

blade. (Saw blade can not be pulled out).

• Retightenthegrubscrew.

• Whenchangingthesawblade,takecare

that the blade holder is free of material

residue (e.g. wood or metal shavings),

• Beforeusingthesawmakesurethesaw

blade is secure.

USE

Fig.C

Make sure that the saw blade does not

rest on or touch any objects when the

machine is switched on.

Switching on

• Puttheon-offtriggerswitch(4).

Switching off

• Releasetheon-offtriggerswitch.

• Theon-offtriggerswitchcanbelockedon

for continuous operation by pressing the

trigger lock button whilst pulling the trigger.

• Toreleasethetriggerlock,simplypullthe

trigger switch again.

SPEED CONTROL

• Duringoperationandwhilstthemachine

is at rest the stroke rate (speed) can be

selected using the thumbwheel (5). The

stroke rate will remain constant even under

load.

RSM1011 Ma # 0810-10.1 FC.indd 4 10/10/08 4:59:41 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm FRS-710 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info