Bedienungsanleitung Ferm GRM1010 (Seite 9 von 12) (Englisch)

763656

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

Ferm

Malfunction

Should the machine fail to function correctly, a

number of possible causes and the appropriate

solutions are given below:

1. When switched on, the machine will not

start working.

• Plug is not well connected or electric socket is

faulty.

• Check plug, socket and fuse.

• The mains voltage is lower than the minimum

requirement for start up.

• Check that the mains voltage is adequate.

• The pump is stuck.

• Refer to after storage instructions. Switch

off the unit and let the motor cool.

• Thermal safety has tripped.

• Leave the lance open with water coming

through.

2. Fluctuating pressure

• Pump sucking air

• Check that hoses and connections are

airtight

• Valves dirty, worn out or stuck. Pump seals

worn.

• Clean and replace or refer to dealer.

3. Water leaking from the pump

• Seals worn out

• Check and replace, or refer to dealer

4. The motor stops suddenly

• Thermal safety switch has tripped due to

overheating.

• Check that the mains voltage corresponds

to specifications. An extension cable, which

is too thin, and tool long can cause a

voltage drop and cause the motor to

overheat. Leave to cool down. Use heavy

duty extension cables.

5. The pump does not reach the necessary

pressure.

• Water inlet, filter is clogged

• Clean the water inlet filter

• Pump sucking air from connections or hoses

• Check that all supply connections are tight

• Suction/ delivery valves are clogged or worn

out.

• Check that the water feeding hose is not

leaking.

• Unloader valve is stuck

• Clear or respire valves

• Lance nozzle incorrect or worn out

• Loosen and re-tighten regulation screw

Check and/ or replace.

Repairs and servicing should only be

carried out by a qualified technician or

service firm.

Cleaning

Keep the ventilation slots of the machine clean to

prevent overheating of the engine.

Clean the housing regularly with a soft cloth,

preferably every time it is used.

Keep the air vents free f dust and dirt. Remove

stubborn dirt with a soft rag moistened in soapy

water. Do not use any solvents such as petrol,

alcohol, ammonia, etc. as such substances can

damage the plastic parts.

Lubrication

The appliance does not need any extra lubrication.

Storage and transportation

Keep the high pressure washer in well-ventilated

dry premises with temperature not going below

+5ºC. Operate the cleaner with non-corrosive/non-

toxic antifreeze before storing for the winter.

Faults

If a fault arises through wear in an element, please

contact the service address shown on the

warranty card. A drawing of the spare parts that

may be obtained is included at the end of these

operating instructions.

Environment

To prevent damage during transport, the appliance

is delivered in a solid packaging which consists

largely of reusable material. Therefore please

make use of options for recycling the packaging.

Damaged and/or disposed of electrical

or electronic devices must be dropped

off at recycling stations intended for that

purpose.

Warranty

Read the terms of warranty on the separate

warranty card which is enclosed.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm GRM1010 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info