Bedienungsanleitung Ferm GTM1003 (Seite 10 von 26) (Englisch)

763651

Zoom out

Zoom in

Vorherige Seite

1/26

Nächste Seite

When using the machine sideways

always use the sidewheel

Mounting of the side wheel (Fig. E)

• Slide side wheel (13) over the side wheel

holder (14).

Mounting the wire spool (Fig. F1)

• Place the spring (17) into the spool housing

(18). Make sure the wider side of the spring is

placed on the trimmer head.

• Place the spool reel (16) over the spring (17).

Make sure the wires are passed through the

holes inside the housing (18). (Fig. F2)

• Cover the spool reel with the spool cover (15)

and fasten it by turning the cover tightly.

Before replacing the spool clean the

machine from any dirt.

Replacing the spool (Fig. F1)

• Remove the spool cover (15)

• Take out the spool reel (16) but leave the spring

(17) inside.

• Take the new spool reel (GTA1002) and place

it over the spring (17). Make sure the wires are

passed through the holes inside the housing

(18). (Fig. F2)

• Cover the new spool reel with the spool cover

(15) and fasten it by turning the cover tightly.

Using the tap and go system (Fig. G)

• When the wire is too short, switch the machine

on and press the tip of the spool reel (19) on

the ground (make sure this is done on a hard

surface).

• This will release the wire in order to get longer.

• The wire will be cut on the correct length

automatically by the blade mounted in the

protection guard (10).

Please keep power switched off and

disconnect the battery.

Tilting the trimmer head (Fig. H)

• Press the knob (20) of the trimmer head to tilt

the head in the desired position.

• When knob is released, the head will click and

lock in the chosen position

Turning the trimmer head (Fig. I)

• Press the ring (21) down towards the trimmer

head to turn the head in the desired position.

• When the ring is released, the head will click

and lock in the chosen position

Adjusting the pole height (Fig. J)

• To adjust the height of the machine, loosen the

lower adjustment ring (22)

• Carefully push the lower shaft (24) from the

upper shaft (23) down or upwards.

• Fasten the lower adjustment ring (22) to secure

the height of the machine

Before use, always visually inspect the

machine and its parts are correctly

mounted, not worn out or damaged.

Using your grass trimmer

• For your own safety and for best results read

the following user advice and do not use this

product for anything other than its intended

purpose.

• This grass trimmer is made for cutting grass.

All other use that is not specifically allowed in

this manual may lead to damage to the grass

trimmer or injury to the user.

Safety features

• The protection guard has a knife for cutting

the wire to the correct length. Do not touch the

knife to reduce the chance of injury to the user.

• The on/off switch (6) and safety switch (7)

must be operated together to start the motor.

If pressure on one of two switches is released,

the tool is designed to stop rapidly.

Switching On and Off

• To switch the trimmer on, press the safety

switch (7) and the start on/off switch (6) at the

same time.

• To switch off, release one or both switches.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm GTM1003 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info