Bedienungsanleitung Ferm hdm 1017 (Seite 6 von 124) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

388771

Zoom out

Zoom in

Vorherige Seite

1/124

Nächste Seite

Exchanging and removing drill bits

Fig. A + B

Before exchanging bits, rst remove the

power plug from the wall socket.

Inspect bits regularly during use. Blunt

bits should be re-sharpened or replaced.

• Lightly oil the bit shaft before inserting it into

the chuck.

• Slide the locking sleeve (7) to the rear, and

insert the bit into the chuck opening. Ensure

that the keyway in the bit is seated properly in

the chuck, by carefully turning the bit until it

clicks into place. Release the locking sleeve.

• To remove the bit, slide and hold the locking

sleeve to the rear.

Setting depth gauge

Fig. A

• Loosen the handgrip by turning it

anticlockwise.

• Insert the depth gauge ruler through the hole

in the auxiliary handgrip.

• Slide the ruler to the desired depth.

Retighten the screw rmly.

Function selection switch

Fig. C

The correct position of the selection switch for

each machine function is given in the diagram

(Fig.C) on page 3.

A: Drilling

B: Hammer Drilling

C: Chisel angle adjustment

D: Demolition hammer/chisel

The On/Off switch

Fig. A

• Switch the machine on by pressing the

triggerswitch (2). When you release the

triggerswitch (2) the machine will turn off.

Switch-lock

• You can lock the On/Off switch by pressing the

triggerswitch (2) and then pressing knob (4).

Release the switch-lock by pressing the

triggerswitch (2) shortly.

Speed-control

• The rotation-speed can be continuously

adjusted from 0 to 950 and 0 to 4500 rotations

per minute by pressing the switch (2) deeper

or less deep.

Adjusting of the maximum rotation speed

• Switch the machine on by pressing

triggerswitch (2).

• Lock the triggerswitch (2) by pressing knob

(4).

• Adjust the speed by turning the small wheel

(3) to the desired maximum rotation speed.

Switching the direction of rotation

• Direction of rotation counter-clockwise: shift

switch to “►”.

• Direction of rotation clockwise: shift switch to

“◄”.

This function is only available when the machine

is set to “drill mode”.

Chuck

A chuck with SDS-10 shaft is shipped with the

product. Please note that the machine is

particularly suited for hammer drilling, the chuck

should only be used for occasional simple drill

work.

• Use the chuck key to open and close the

chuck.

• Introduce the chuck key into one of the three

holes in the chuck and open the chuck by

turning anticlockwise, close the chuck by

turning clockwise.

• Always remove the chuck key from the chuck.

Never run the machine with the chuck key

inserted.

• Ensure that the switch (2) is in the OFF

position.

• Only connect the device to the mains power if

this is the case.

User tips

Always use the machine with the auxiliary

handgrip rmly anchored in place – you will not

only work with more comfort, you will also work

with more precision.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm hdm 1017 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info