Bedienungsanleitung Ferm HDM1038P (Seite 6 von 108) (Alle Sprachen)

764194

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

Exchanging and removing drill bits

Fig. A - B

Before exchanging bits, first remove the

power plug from the wall socket.

Inspect bits regularly during use. Blunt

bits should be re-sharpened or replaced.

Lightly oil the bit shaft before inserting it

into the chuck.

• SDS drills can be inserted by pushing the drill

into the chuck until a click can be heard. If

needed rotate the SDS drill a little to ensure the

keyway in the bit fits the chuck well.

DO NOT slide the locking sleeve (7) to the

rear when inserting bits.

• To remove the SDS drill, slide the locking

sleeve (7) to the rear and remove the SDS drill

while keeping the sleeve (7) in this position.

Setting depth stop

Fig. A

• The depth stop ruler can be added to the side

handle by pushing the dept stop button (9).

• Keep pushing the depth stop button (9) and

insert the depth stop ruler (8) through the hole

on the side handle ring.

• Slide the ruler to the desired depth.

• Loosen the depth stop button (9).

The On/Off switch

Fig. A

• Switch the machine on by pressing the On/Off

switch (2). When releasing the On/Off switch

(2) the machine will turn off.

• The rotation-speed can be continuously

adjusted by pressing the On/Off switch (2)

deeper or less deep.

Lock-on button

Fig. A

• Lock the On/Off switch (2) by pressing the On/

Off switch (2) and then pressing the lock-on

button (4).

• Release the switch-lock by shortly pressing

the On/Off switch (2) again.

Switching the direction of rotation

Fig. A.

• Direction of rotation counter-clockwise: shift

left/right switch (1) to “ ”.

• Direction of rotation clockwise: shift left/right

switch (1) to “ ”.

This function is only available when the machine

is set to “drill mode” (As shown in fig. D function

A & B).

Function selection switch

In order to avoid damage to the machine,

adjusting the function selection switch (5)

shall only be done when machine is not

running. Fig. C

Fig. D

The correct position of the function selection

switch (5) for each function is shown in the

pictures in fig. D. Always make sure the function

switch clicks in the desired position.

A) Drilling (without hammer function): for drilling

in several materials.

B) Hammer Drilling (with hammer function): for

drilling in masonry such as brick, concrete and

similar material.

C) Chisel angle adjustment: for changing the

angle of the chisel. When set under right angle

switch back to position D. before using the

tool.

D) Chipping (chisel function): for chipping and

small demolition jobs.

User tips

Always use the machine with the side handle

firmly anchored in place - you will not only work

with more comfort, you will also work with more

precision.

Caution: drills and chisels can get very

hot.

Drilling and hammer drilling (function A and B)

• For large holes, for instance in very hard

concrete, start using a smaller bit for pilot

drilling first, then drill to nominal size.

• Hold the machine firmly with 2 hands. Be

aware the drill can jam and because of that

machine might suddenly turn (especially when

drilling deep holes).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm HDM1038P Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info