Bedienungsanleitung Ferm HTM1002 (Seite 8 von 38) (Englisch, Holländisch)

762313

Zoom out

Zoom in

Vorherige Seite

1/38

Nächste Seite

Warning!

You may not use the hedge trimmer without the

safety protection guard

Mounting the safety guard (Fig. B)

Fit the safety protection guard (8) over the blade

and mount in onto the side of the housing using

the screw (10) delivered.

Using your hedge trimmer

• For your own safety and for best results read

the following user advice and do not use this

product for anything other than its intended

purpose.

• This hedge trimmer is made for cutting

hedges and bushes. All other use that is not

specifically allowed in this manual mat lead to

manage to the hedge trimmer or injury to the

user.

Safety transport

• The hedge trimmer has a transport protection

cover for save transportation of the machine.

Safety features

• The fixed blade teeth have extended points

with rounded ends to reduce the chance of

injury in case of accidental contact.

• The fixed blade is longer than the moving

blade to guard against kickback should you

inadvertently make contact with a wall or

fence.

• The rear handle trigger switch (6) and front

handle bar switch (9) must be operated

together to start the motor. This ensures that

both hands are used to control the trimmer.

• If pressure on one of two switches is released,

the tool is designed to stop rapidly.

Switching On and Off

• To switch the trimmer on, press the safety

switch (9) and the start switch (6) at the same

time.

• To switch off, release one or both switches.

Trimming a hedge - best method

• Apart from hedges the hedge trimmer may

also be used for cutting bushes.

• The best cutting effect is achieved when

holding the blade at an angle to the of approx.

15°.

• The opposite rotating knives cut on both sides,

and it is therefore possible to trim the hedge in

both directions.

• The side of the hedge are trimmed using

curved shaped movements from the bottom

and upwards.

• Ideally a hedge should be wider at the

bottom than the top. This will improve light

penetration, keeping the hedge healthy. If

possible, trim both sides of the hedge.

• When trimming the sides of the hedge, trim

from the bottom upwards. This will ensure

there are no hedge trimmings obscuring or

interfering with your cut strokes. The blade

should not be forced to cut too deep. Cut

lightly through the surface of the hedge.

• When trimming the top of the hedge, trim

away from you but do not over-reach. It is

much wiser and safer to move along and cut

within your reach remaining on two feet at all

times. Do not let the blade come into contact

with wire meshing or fencing material. It could

damage the material and your trimmer.

4. MAINTENANCE

Before cleaning and maintenance, always

switch off the machine and remove the

battery pack from the machine.

Clean the machine casings regularly with a soft

cloth, preferably after each use. Make sure that

the ventilation openings are free of dust and

dirt. Remove very persistent dirt using a soft

cloth moistened with soapsuds. Do not use any

solvents such as gasoline, alcohol, ammonia,

etc. Chemicals such as these will damage the

synthetic components.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm HTM1002 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info