Bedienungsanleitung Ferm JSM1030 (Seite 7 von 64) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Polnisch, Türkisch, Schwedisch, Finnisch)

764184

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

Mounting and removing the saw blade

Refer to the table below to select the required saw

blade.

Saw blade Material

Coarse Wood

Medium Wood

Fine Steel, aluminium, plastic

Very fine Wood (curves)

Remove the guard from the machine to change

the saw blade.

Always saw with guard.

Fitting a saw blade

Fig. 2

The machine is equipped with a quick blade

exchange system.

• Turn the clamping ring (13) of the saw blade

holder (5) completely to the left, in order to

open up the holder.

• Insert the saw blade (15) in the saw blade

holder (5) as far as possible. The teeth of

the saw blade (15) must point upward and

forward. The smooth side of the saw blade

must engage in the slot of the guide roller (6).

• Release the clamping ring (13) to close the

holder.

• Make sure when changing the saw blade that

the blade holder (5) is free of material debris

(such as splinters of wood or metal).

• Before use, always check that the saw blade is

securely fixed.

Removing the saw blade

• Turn the clamping ring (13) of the saw blade

holder (5) completely to the left, in order to

open up the holder.

• Remove the saw blade from its holder.

• Release the clamping ring (13) to close the

holder.

4. USE

Switching on and off

Fig. 3

• To switch on the machine, press the on/off

switch (1).

• To switch the machine to continuous mode,

keep the on/off switch (1) pressed and

simultaneously press the lock-on button (2).

• To switch off continuous mode, press the on/

off switch (1) again.

• To switch off the machine, release the on/off

switch (1).

Setting the speed

Fig. 3

The speed adjustment wheel (3) is used for setting

the speed. The ideal speed depends on the profile

and the teeth of the saw blade and on the material

to be worked.

Do not set the speed during use.

• Turn the speed adjustment wheel (3) to the

required position.

- For hard materials, use a saw blade with

fine teeth and select a lower speed.

- For soft materials, use a saw blade with

coarse teeth and select a higher speed.

Setting the mitre angle

Fig. 4

The mitre angle is variable between 0° and 45°.

The mitre angle can be read from the scale.

Do not set the mitre angle during use.

•

Slacken the Hex screws(14) using the Hex key(8).

• Tilt the Base plate (7) to the required position.

•

Tighten the Hex screws(14) using the Hex key(8).

Dust extraction

Fig. 5

• Insert the dust extraction adapter (11) into the

dust extraction connection (10).

• Connect the hose of a vacuum cleaner to the

dust extraction adapter (11).

Hints for optimum use

• Clamp the workpiece. Use a clamping device

for small workpieces.

• Draw a line to define the direction in which to

guide the saw blade.

• Firmly hold the machine by the grip.

• Set the sawing speed.

• Set the mitre angle.

• Switch on the machine.

• Wait until the machine has reached full speed.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm JSM1030 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info