Bedienungsanleitung Ferm LMM1012 (Seite 11 von 88) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Polnisch)

763901

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

Technical specifications

Model no. LMM1012

Voltage 230-240 V~

Frequency 50Hz

Power 1300 W

No load speed 3300/min

Cutting width 320 mm

Cutting height 25/40/55mm

Grass box capacity 30L

Weight 8.1 kg

Protection level IPX4

LPA (sound pressure) 85dB(A) K=3dB(A)

LWA (sound power) 96dB(A) K=3dB(A)

Vibration value <2.5m/s2 K=1,5ms2

Vibration level

The vibration emission level stated in this

instruction manual has been measured in

accordance with a standardised test given in

EN60335; it may be used to compare one tool

with another and as a preliminary assessment of

exposure to vibration when using the tool for the

applications mentioned.

- using the tool for different applications, or with

different or poorly maintained accessories,

may significantly increase the exposure level.

- the times when the tool is switched off or when

it is running but not actually doing the job, may

significantly reduce the exposure level.

Protect yourself against the effects of vibration by

maintaining the tool and its accessories, keeping

your hands warm, and organizing your work

patterns.

Description

The numbers in the text refer to the diagrams on

page 2-5.

1. Upper handle

2. On/off switch

3. Safety button

4. Power socket

5. Cable strain relief

6. Cable holder

7. Carrying handle

8. Wheel

9. Wheel cover

10. Grass box basket

11. Grass box lid

12. Grass box cover

13. Grass level indicator

14. Lower handle

15. Knob for handle

3. ASSEMBLY

Before carrying out any work on the

machine, disconnect the mains plug

from the power supply

Assembling the lower handle

Fig. A, B, C

1. Insert the lower handle (14) into the intended

hole of the lawn mower body, as shown on

figure B. Ensure the hole in the lower handle (14)

aligns with the hole in the lawn mower body.

2. Insert the screw in the hole and tighten by

turning clockwise, as shown on figure C.

3. Repeat these steps for the other lower handle

(14).

Assembling the upper handle

Fig. A, D, E, F

1. Put the cable strain relief (5) on the right side of

the upper handle (1) as shown on figure D.

2. Attach the upper handle (1) to the lower handle

(14), using the supplied bolts and handle

knobs (15) as shown on figure E. Make sure

the on/off switch (2) assembly is on the right

side when standing behind the lawn mower.

3. Fixate the cable to the handle by using the

cable holders (6), as shown on figure F.

Note: When handle knobs (15) are loosened, the

upper handle (1) can be folded down for storing

the lawn mower. Ensure that the power cable is

not caught.

Mounting the wheels

Fig. A, G, H

1. Attach a wheel (8) on the axle. Afterwards, put

a supplied metal washer onto the axle.

2. Insert the supplied metal split pin in the

opening of the axle. Afterwards, fold the metal

split pin around the axle, as shown on figure G.

3. Mount the wheel cover (9) onto the wheel (8).

Make sure the plastic pins on the wheel cover

(9) align with the holes of the wheel (8).

4. Repeat these steps for the other wheels.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm LMM1012 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info