Bedienungsanleitung Ferm LMM1012 (Seite 12 von 88) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Polnisch)

763901

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

Assembling the grass box

Fig. A, I, J, K

It is possible to use the lawn mower with or

without grass box. Remember though that when

cutting without the grass box, the grass box lid

(11) must be lowered. Do not operate the mower

with outlet lid lifted.

1. Join the two halves of the grass box basket

(10), as shown on figure I.

2. Mount the grass box cover (12) onto the

assembled grass box basket (10), as shown on

figure J.

3. Lift the grass box lid (11) and attach the

assembled grass box onto the lawn mower.

Ensure the indents in the grass box align

properly with the holders of the lawn mower

body.

Note: the grass box is fitted with a grass level

indicator (13), which shows the amount of mowed

grass. As long as the grass box is not full, the

indicator will be opened. When the grass box

is full, the indicator will close. In that case

immediately stop mowing and empty the grass

box. This indicator is only a rough guideline, of

which the functionality depends on the condition

inside the grass basket.

Replacing the cutting blade

Fig. A, P

Before carrying out any work on the

machine, disconnect the mains plug

from the power supply

When replacing the cutting blade, wear

protective gloves. Danger of injury when

touching the cutting blade.

Only use blades that are recommended

by the manufacturer.

1. Remove the grass box.

2. Turn the mower onto its side.

3. Firmly hold cutting blade using protective

gloves.

4. Turn the cutting blade fixing screw counter-

clockwise to loosen it, as shown on figure P.

5. Replace or sharpen the cutting blade.

6. Install the cutting blade, use the above

procedure in reversed order (holes in the

cutting blade must be seated on the spindle

pins).

7. It is best to entrust sharpening or replacement

of cutting blade to a qualified person. Only

original parts should be used.

All defects should be repaired by service

workshop authorized by the manufacturer.

4. OPERATION

Before using, always visually inspect to

see that the blades, blade bolts and

cutter assembly are not worn or

damaged. Please keep power switched

off and disconnect the power supply.

Replace worn or damaged blades and

bolts in sets to preserve balance.

Adjusting the cutting height

Fig. A, L, M

Switch off the equipment, disconnect

the plug and wait for the blade to stop.

There is a risk of injury.

Depending on the preferred cutting height, you

can adjust the wheel assembly in one of three

positions.

1. Put the lawn mower on its side.

2. Grasp the wheel axle on both sides.

3. Pull evenly on the axle and insert into one

of the three notches, as shown on figure L.

Ensure the left and right side of the axle are

mounted in the same notch. Repeat this step

for both axles. Ensure the front and rear axle

are mounted in the same notch, so the lawn

mower cuts parallel to the lawn.

4. Each notch position resembles a cutting

height, as shown on figure M.

Position 1 resembles a cutting height of 25 mm.

Position 2 resembles a cutting height of 40 mm.

Position 3 resembles a cutting height of 55 mm.

Note: A higher cut height should be selected for

the first cut of the season.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm LMM1012 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info