TALLENE I DEN FØLGENDE TEKST
KORRESPONDERER MED AFBILDNINGERNE PÅ
SIDE 2
KAP- OG GERINGSSAV
ADVARSEL!
Af hensyn til sikkerheden skal denne
brugsanvisning gennemlæses omhyggeligt før brug.
INDHOLD:
1. Information om maskinen
2. Sikkerhed
3. Montering af tilbehør
4. Funktion
5. Service & vedligeholdelse
1. INFORMATION OM MASKINEN
INTRODUKTION
Kap- og geringssaven er beregnet til at save træ og
træholdige arbejdsemner.
TEKNISKE SPECIFIKATIONER
PRODUKTINFORMATION
1. Håndtag med afbryder
2. Udløserknap
3. Motorhus (dæksel over kontaktkul)
4. Beskyttelsesskærm over klinge
5. Låseknap til savehovedet
6. Forlængerstykker (venstre og højre)
7. Greb til indstilling af savevinkel
8. Unbrakonøgle
9. Drejeknap til geringssavning
10. Støvpose
11. Skrue
12. Savklingebolt
13. Savklingeflange
14. Kappe
15. Stjernenøgle
16. Unbrakonøgle (lille)
17. Unbrakonøgle (stor)
18. Flangenøgle
19. Laser afbryder
20. Justeringsbolt
KASSEN INDEHOLDER
1 Kap- og geringssav
1 Støvpose
2 Forlængerstykker
5 Gummidupper
1 Flangenøgle
1 Stjernenøgle
2 Unbrakonøgler
1 Brugsanvisning
1 Sikkerhedsinstruktioner
1 Garantibevis
Kontroller maskinen, løse dele og tilbehør for
transportskader.
2. SIKKERHED
Når maskinen bruges, skal man altid nøje følge de
vedlagte sikkerhedsforskrifter og
sikkerhedsinstruktionerne nedenfor.
FORKLARING TIL SYMBOLER
Der er anvendt følgende symboler i instruktionerne og
på selve maskinen:
CE I overensstemmelse med relevante europæiske
sikkerhedsstandarder
Klasse II maskine – dobbelt isoleret – der kræves
ikke jordet stik
Risiko for personskade eller beskadigelse af
materiale.
Læs instruktionerne
Tag straks stikket ud af stikkontakten, hvis
ledningen beskadiges og i forbindelse med
vedligeholdelse
Hold omkringstående på afstand
Brug beskyttelsesbriller og høreværn
Advarsel! Laserstråle! Se ikke ind i laserstrålen og
ret den ikke mod andre personer, når den er tændt.
Defekte og/eller kasserede elektriske eller
elektroniske maskiner skal afleveres på en
genbrugsplads.
FØR SAVEN BRUGES
Kontroller maskinen. Hvis en af delene til maskinen
mangler, er bøjet eller på anden måde ubrugelig, eller
hvis der konstateres elektriske fejl på maskinen, skal der
slukkes for maskinen, og stikket skal tages ud af
stikkontakten. Den manglende, beskadigede eller
defekte del skal udskiftes, før maskinen bruges igen.
Savklingen monteres, og arbejdsemnet fastsættes som
beskrevet nedenfor.
Spænding | 230 V~
Effektforbrug | 1200 W
Omdrejninger, ubelastet | 4500/min
Savklingens dimensioner | 210 x 15.89 mm
Max. savekapacitet 90º | 120 x 50 mm
Max. savekapacitet 45º | 85 x 22 mm
Vægt | 7.6 kg
Lpa (Lydtrykniveau) | 90.7 dB(A)
Lwa (lydintensitet) | 103.7 dB(A)
Vibrationsniveau | 0.894 m/s
2
Ferm 47
MOUNTING THE DUST BAG
Press in the clamp of the dust bag (10) and slide it onto
the opening on the back of the machine. The dust bag
stays in place when you release the clamp.
4. OPERATION
USING THE CROSS-CUT SAW MACHINE
Before use, always check for faults or defects!
• Set the desired sawing angle of the machine.
• Put the plug into the socket.
• Turn on the laser using the switch (19).
• Hold the material tightly on the left side while making
sure that you keep a safe distance from the blade of
the saw.
• Turn on the machine using the switch (1).
• Make sure that the saw blade has reached full speed
before allowing it to touch the piece of work to be
sawn.
• Use knob (2) to raise the protective cover lock.
• Now bring the saw slowly downwards so that the
saw blade saws through the piece of work and passes
through the slot in the table. Do not put any pressure
on the saw. Give the machine time to saw through
the piece of work.
• Bring the machine gently up again and switch it off by
letting go of the switch (1).
PROBLEM SOLVING
1. The motor does not start
• The plug is not in the socket
• The power cord is broken
• The switch is defective. Take the machine to your
Ferm dealer for repair.
2. The saw cut is not even (jagged)
• The saw blade must be sharpened
• The saw blade is mounted back to front
• The saw blade is clogged with resin or sawdust
• The saw blade is not suitable for the piece of work
being used
3. The height and/or mitre lever is obstructed
• Chips and/or dust must be removed
4. The motor has difficulty in reaching full speed
• The extension cord is too thin and/or too long
• The mains voltage is less than 230 V
5. The machine vibrates excessively
• The saw blade is damaged
6. The machine becomes excessively hot
• The ventilation slots are blocked. Clean them out
with a dry cloth.
7. The electromotor runs unevenly
• The carbon brushes are worn out. Replace the
carbon brushes or consult your Ferm dealer.
5. SERVICE & MAINTENANCE
MAINTENANCE
Always make sure that the machine is not
connected to the mains electricity when you carry
out any maintenance of the mechanism.
Ferm machines are designed to function for a long time
without any problems with a minimum of maintenance.
By cleaning the machine regularly and using it in the
correct way you can contribute to a long life of your
machine.
CLEANING
Clean the machine housing regularly with a soft cloth,
preferably after each time you use the machine. Make
sure that the ventilation slots are free of dust and dirt.
For stubborn dirt use a soft cloth dampened with soapy
water. Never use solvents such as benzene, alcohol,
ammonia, etc. These types of solvents can damage the
plastic parts.
LUBRICATION
The machine does not need any extra lubrication.
FAULTS
Should a fault occur, e.g. after wear of a part, please
contact the service address on the warranty card. In the
back of this manual you find an exploded view showing
the parts that can be ordered.
ENVIRONMENT
To prevent damage during transport, the appliance is
delivered in a solid packaging which consists largely of
reusable material. Therefore please make use of options
for recycling the packaging.
Faulty and/or discarded electrical or electronic
apparatus have to be collected at the appropriate
recycling locations.
6 Ferm
