Bedienungsanleitung Ferm MSM1031 (Seite 8 von 120) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

493544

Zoom out

Zoom in

Vorherige Seite

1/120

Nächste Seite

(fig. 7).

• For sawing bevel cuts, the guide fence insert

must be removed from the machine as shown

(fig. 7)



• Mount the support bracket into the slot in the

rear of the base.

• Tighten the screw to secure the support

bracket.

Changing the saw blades

Fig. 4

Only use saw blades that are sharp and

undamaged. You must immediately

replace chipped or bent saw blades.

• Make sure that the plug is not in the socket!

• Lock the head of the machine in its highest

position.

• Move the hood (6) forwards. Push the saw

blade interlock (22) in and unscrew the bolt

(18) with the key supplied (clockwise).

• Remove the saw blade flange (19) and

change the blade. Make sure that the blade is

mounted in the machine correctly: with the

arrow on the blade pointing clockwise.

• Replace the flange (19) and push the interlock

(22) in and screw the bolt (18) tight again.

Adjusting the saw angle

• Unscrew the knob (9) a half turn clockwise.

• Turn the machine to the desired angle (the

angle can be read off on the front of the

machine).

• Screw up the knob (9) a half turn

anticlockwise.

Setting up the double sawing angle / mitring

Fig. 2 + 3

• Adjust the first angle as described for

adjusting the saw angle (above).

• Turn the knob (12) anticlockwise and then set

the angle desired (you can read this off on the

back of the machine. Then tighten the knob

(12) again by turning it clockwise.

Changing the carbon brushes

Fig. 1

• Make sure that the plug is not in the socket!

• Unscrew the covers (4) with a flat bladed

screwdriver. Remove the carbon brushes with

the same type of brushes. Screw the covers

(4) tight again.

Note: Always replace both carbon brushes at the

same time. Never use a mixture of old and new

brushes.

Mounting the dust bag

Fig. 3

Press in the clamp of the dust bag and slide it

onto the opening (13) on the back of the machine.

The dust bag stays in place when you release the

clamp.



Using the mitre saw

Fig. 1

Before use, always check for faults or

defects!

• Set the desired sawing angle of the machine.

• Put the plug into the socket.

• Fix the piece of work in place using the

clamps (7): make sure that the material is well

clamped in place!

• Hold the material tightly on the left side while

making sure that you keep a safe distance

from the blade of the saw.

• Turn on the machine using the switch (1).

• Make sure that the saw blade has reached full

speed before allowing it to touch the piece of

work to be sawn.

• Use knob (3) to raise the protective cover

lock.

• Now bring the saw slowly downwards so that

the saw blade saws through the piece of work

and passes through the slot in the table. Do

not put any pressure on the saw. Give the

machine time to saw through the piece of

work.

• Bring the machine gently up again and switch

it off by letting go of the switch (1).

Using the slide-function

Fig. 2

The machine must be firmly bolted to a

workbench.

Use the slide-function for sawing wide

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm MSM1031 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info