Bedienungsanleitung Ferm MSM1034 (Seite 10 von 72) (Deutsch, Englisch, Holländisch, Französisch, Spanisch, Polnisch)

510120

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

10 Ferm

b. As a stationary machine on the subframe. In

this case the machine must be secured to the

subframe with 4 bolts and the subframe

anchored to the floor or to a floor plate with

dimensions of at least 1 square meter.

Guide fence insert

Fig. H, I, J

For safety reasons, this machine is equipped with

a guide fence insert

to be used when using the machine for sawing

straight cross-cuts.

• For sawing straight cross-cuts, the guide

fence insert must remain mounted on the

machine (fig. H).

• For sawing mitre cuts, the guide fence insert

must be removed from the machine as shown

(fig. H).

• For sawing bevel cuts, the guide fence insert

must be removed from the machine as shown

(fig. I+J).

Mounting and removing the saw blade

Fig. A+B

Do not use the machine without the

guard.

Mounting

• Pull out the locking knob (3) and raise the saw

head (12).

• Loosen the bracket (29) by removing the

screw (30).

• Raise the guard (6).

• Keep the spindle lock button (7) pressed and

loosen the bolt (19) using the spanner (20).

• Remove the flanges (21 & 22).

• If necessary, clean the flanges (21 & 22).

• Mount the flange (22).

• Mount the saw blade (5). Make sure that the

arrow on the saw blade points in the same

direction as the arrow on the saw head.

• Mount the flange (21).

• Keep the spindle lock button (7) pressed and

tighten the bolt (19) using the spanner (20).

• Lower the guard (6).

• Mount the bracket (29) by tightening the screw

(30).

Removing

• Pull out the locking knob (3) and raise the saw

head (12).

• Loosen the bracket (29) by removing the

screw (30).

• Raise the guard (6).

• Keep the spindle lock button (7) pressed and

loosen the bolt (19) using the spanner (20).

• Remove the flange (21).

• Remove the saw blade (5).

• Mount the flange (21).

• Keep the spindle lock button (7) pressed and

tighten the bolt (19) using the spanner (20).

• Lower the guard (6).

• Mount the bracket (29) by tightening the screw

(30).

Setting the mitre angle

Fig. C

• The mitre angle is left/right variable between

0° and 45°. The mitre angle can be read from

the scale (9).

Do not set the mitre angle during use.

• Slacken the locking knob (8).

• Turn the saw table (13) to the required

position.

• Tighten the locking knob (8).

Setting up the double sawing angle / mitring

Fig. D

• Adjust the first angle as described for

adjusting the saw angle (above).

• Turn the knob (10) anticlockwise and then set

the angle desired (you can read this off on the

back of the machine. Then tighten the knob

(10) again by turning it clockwise.

Changing the carbon brushes

Fig. A

• Make sure that the plug is not in the socket!

• Unscrew the covers (16) with a flat bladed

screwdriver. Remove the carbon brushes with

the same type of brushes. Screw the covers

(16) tight again.

Note: Always replace both carbon brushes at the

same time. Never use a mixture of old and new

brushes.

Mounting the dust bag

Fig. F

Press in the clamp of the dust bag (27) and slide it

onto the opening on the back of the machine. The

dust bag stays in place when you release the clamp.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm MSM1034 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info