Bedienungsanleitung Ferm MSM1040 (Seite 8 von 160) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Türkisch)

762257

Zoom out

Zoom in

Vorherige Seite

1/160

Nächste Seite

compatible with this power tool could pose a

risk to persons.

• Never remove cuttings, wood chips, etc.

from the cutting area while the power tool is

running. Always guide the tool arm back to the

neutral position first and then switch the power

tool off.

• Do not touch the saw blade after working

before it has cooled. The saw blade becomes

very hot while working.

• Never make warning signs on the machine

unrecognisable.

• If laser radiation hits your eye, you must

close your eyes and immediately turn your

head away from the beam.

• Do not use any optical instruments such

as binoculars to view the radiation source.

Doing so can damage your eye.

• Do not direct the laser beam at persons who

are looking through binoculars or similar

instruments. Doing so can damage their eye.

• Do not make any modifications to the laser

equipment. The setting options described in

these operating instructions can be used safely.

• Do not stand in line with the saw blade in

front of the power tool. Always stand to the

side of the saw blade. This protects your body

against possible kickback.

• Keep hands, fingers and arms away from the

rotating saw blade.

• Do not reach one hand across the other

when in front of the tool arm.

• Avoid overheating of the saw teeth. When

the saw blade overheats, stop the machine.

Allow the saw blade to cool down before using

the machine again.

• Replace damaged or worn saw blades

immediately.

• Only use saw blades that match the

specifications given in this operating manual

and that have been tested and marked in

accordance with EN 847-1.

• When sawing curved or round workpieces,

these must be especially secured against

slipping. At the cutting line, there should

be no gap between the workpiece, fence

and saw table. If necessary, you will need to

manufacture special fixtures.

Electrical safety

When using electric machines always observe the

safety regulations applicable in your country to

reduce the risk of fire, electric shock and personal

injury. Read the following safety instructions and

also the enclosed safety instructions.

Always check that the power supply

corresponds to the voltage on the rating

plate.

Replacing cables or plugs

Immediately throw away old cables or plugs

when they have been replaced by new ones. It is

dangerous to insert the plug of a loose cable in

the wall outlet.

Using extension cables

• As a supply for this machine always use an

unloaded line and/or an extension cable with

conductors of at least 1,5 mm2 and protected

with a 16 A fuse. Be sure that this extension

cable is not longer than 20 metres.

• This machine can be switched to the

singlephase network (230-240 V/50 Hz). If you

are in doubt about the earth of the electricity

provisions, consult an electrician first.

2. MACHINE INFORMATION

Intended use

The electro tool is intended as a stationary machine

for making straight lengthways and crossways cuts

in wood. Horizontal mitre angles of -45° to +45° as

well as vertical bevel angles of -45° are possible.

Technical specifications

Mains voltage 230-240 V, 50Hz

Capacity 1900 W

Machine class II (double insulated)

No load speed 5.000/min

Saw blade measurement 254x2.4x30mm

Angle for mitring 45º (left and right)

Angle for bevelling 45º (only left)

Mitre saw maximum sawing capacity:

Mitre 0º, Bevel 0º 70x310mm

Mitre 45º, Bevel 45º 40x210mm

Mitre 45º, Bevel 0º 70x210mm

Mitre 0º, Bevel 45º 40x310mm

Weight 12.55 kg

Lpa (sound pressure) 94.5+3 dB(A)

Lwa (acoustic capacity) 108.4+3 dB(A)

Vibration level <2.5 m/s2

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm MSM1040 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info