Bedienungsanleitung Ferm MSM1040 (Seite 15 von 160) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Türkisch)

762257

Zoom out

Zoom in

Vorherige Seite

1/160

Nächste Seite

fence (9) until the leg of the angle gauge is

flush with the saw blade along its entire length;

4. Retighten all four fence bolts (51) again.

Subsequently check the position of the angle

indicator (17). If necessary loosen the pointer

using a Philips screwdriver, set to position 0°

on the scale for mitre angle (16) and re-tighten

the retaining screw.

5. MAINTENANCE

Always make sure that the machine is

not connected to the mains electricity

when you carry out any maintenance of

the mechanism.

Clean the machine casings regularly with a soft

cloth, preferably after each use. Make sure that

the ventilation openings are free of dust and

dirt. Remove very persistent dirt using a soft

cloth moistened with soapsuds. Do not use any

solvents such as gasoline, alcohol, ammonia,

etc. Chemicals such as these will damage the

synthetic components.

Cleaning the protective guards

Always check the protective guard (4) and

retractable protective guard (5) for debris before

using the machine. Remove old sawdust and

splinters using a brush or similar tool.

Replacing the table insert

Immediately replace damaged table

inserts.

With a damaged table insert (13) there is a risk of

small parts getting stuck between table insert and

saw blade, blocking the saw blade. To replace the

table insert:

1. Remove screws of table insert using a Philips

screw driver. If required, adjust mitre and bevel

angle to obtain access these screws;

2. Remove table insert;

3. Install new table insert;

4. Tighten the screws using a Philips screw

driver.

Slide rails

Dirt can damage the slide rails (25) and thereupon

the operating of the machine.

• Clean the slide rails regularly with a soft cloth;

• Drip some lubricating oil on the slide rails;

• Move the mitre saw forwards and backwards

so the oil spreads over the complete rails.

ENVIRONMENT

To prevent damage during transport the machine

is delivered in sturdy packaging. The packaging

is made of recyclable material wherever possible,

so make use of the possibility of recycling the

packaging. When you replace a machine, take the

old one to your local dealer. Here it will be dealt

with in an environmentally friendly way.

Damaged and/or disposed of electrical

or electronic devices must be dropped

off at recycling stations intended for that

purpose.

Only for EC countries

Do not dispose of power tools into domestic

waste. According to the European Guideline

2012/19/EU for Waste Electrical and Electronic

Equipment and its implementation into national

right, power tools that are no longer usable must

be collected separately and disposed of in an

environmentally friendly way.

WARRANTY

Read the warranty conditions on the separately

supplied warranty card.

The product and the user manual are subject

to change. Specifications can be changed

without further notice.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm MSM1040 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info