Bedienungsanleitung Ferm PGM1012 (Seite 6 von 56) (Deutsch, Englisch, Holländisch, Französisch, Spanisch, Polnisch, Schwedisch, Finnisch)

632697

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

6 Ferm

• Clean up any spilled fuel

• Do not smoke while operating the generator

Always use caution!

Starting the generator

Fig. 1 + 4 + 5

1. Turn on fuel tap (15).

2. Turn on engine switch (12).

3. Move choke lever (13) to closed position (to

restart a warm engine, leave the choke lever in

open or half-open position).

4. Pull slowly on the starter cord until it engages,

then pull sharply to start the engine (14).

5. Allow the engine to run until it warms up, and

then move the choke lever to the open position

(13).



• Start the generator.

• Plug in the electrical appliance plug.

• Press AC current protector downward to

“ON”(7).

• The voltmeter (11) displays the voltage on the

AC socket. Normally this should be ± 230 V

during use.

Stopping the generator

Fig. 1 + 5

1. Unplug all cords (5)

2. Turn engine switch to “OFF” (12)

3. Turn off fuel tap (15)

4. Service & Maintenance

Periodic maintenance



• Check engine oil level

• Check fuel hose for cracks or other damage.

Replace if necessary.

• Check exhaust-system for leakage. Retighten

or replace gasket if necessary.

• Check choke operation

• Check recoil starter operation

1st Month or 20 hrs

• Replace engine oil



• Check condition of spark plug. Adjust gap and

clean. Replace if necessary.

• Clean, replace if necessary.

6 Months or 100 hrs

• Replace engine oil

• Clean fuel tap and fuel tank filter. Replace if

necessary.

• Check fittings and fasteners. Replace if

necessary.

12 Months or 300 hrs

• Contact a specialized service centre to check

the valve clearance.

• Check the fan of the cooling system for

damage.

Service – notes on maintenance

Fig.1

Oil replacement

• Warm up engine on level ground

• Remove filler cap (8)

• Open drain plug (9) and let oil drain completely

into a pan placed under the engine.

• Check gaskets, replace if required. Refit drain

plug and refill engine with clean oil.

• Replace filler cap.

Spark plug inspection

Fig. 3

• Disconnect the spark plug cap, and remove

any dirt from around the spark plug area.

• Remove spark plug (17) with the plug spanner

supplied.

• Inspect the spark plug. It should be a tan

colour.

• Measure the gap (distance contact point) with

a suitable gauge. The gap should be 0,7 - 0,8

mm. Correct the gap, if necessary, by carefully

bending the side electrode.

• Replace the spark plug if the electrodes are

worn, or if the insulator is cracked or chipped.

• Install the spark plug carefully, by hand, to

avoid cross-threading.

• Place the spark plug with correct torque: 20

Nm.

• Attach the spark plug cap.

Exhaust screen

• Wait for exhaust to cool.

• Exhaust screen may be blocked up with

carbon deposits.

• Undo the screw cap and remove the exhaust

screen.

• Clean the screen with a wire brush and refit.

• Replace exhaust screen if damaged.



Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm PGM1012 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info