Bedienungsanleitung Ferm RSM1014 FPRS-1800 (Seite 5 von 52) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

539202

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

Ferm 5

• Wearaprotectivemaskwhensawingother

brousmaterials.

• Removeadjustingkeysandwrenches

before turning the tool on.

• Secureyourworkpiecewithclamps.

• Movemachinetowardstheworkpieceonly

when switched on.

• Alwaysholdmachinewithbothhandsand

ensure that you have a safe footing while

working.

• Themachinemaybeoperatedonlywiththe

foot plate mounted. When sawing, the foot

plate must always rest on the workpiece.

• Incorrecthandlingmaydamagethe

machine. Therefore always comply with the

following instructions.

• Useonlysharpsawbladesinperfect

condition; replace cracked, distorted or

blunt saw blades immediately.

• Machineshouldonlybeswitchedonwith

blade installed.

• Selecttools,strokerateandpendulum

actions according to material, Take care to

maintain a constant reed rate.

• Donotattempttostopthesawbladewith

lateral pressure after switching off.

• Onlyusegenuineaccessories.

3. MOUNTING ACCESSORIES

Prior to mounting an accessory always

remove the battery.

Assembling saw blade

Fig. B

To assemble the saw, proceed as follows:

• Slidethesawbuckleclamp(2)inwardand

hold.

• Placethesawinthesawbuckle.Makesure

that the teeth point downwards.

• Pushthesawasfarintothebuckleas

possible.

• Securethesawbygentlyreleasingthesaw

buckle clamp.

Adjusting the foot plate position

Fig. C

When the blade loses its sharpness at some

sections of it’s cutting edge, reposition the

foot plate to use a sharp, unused portion of its

cutting edge.

Besides this, the foot plate can also be used

for adjusting maximum saw depth, especially

useful when sawing in hollow walls.

• Thefootplatecanbeextendedbyloosening

the two footplate mounting screws (9) using

the 4 mm hexagon key and then pulling the

footplate out to the required length.

Ensure the footplate adjustment screws are

secure before resuming work.

Connecting and removing the battery

Fig. A+D

• Insertthebatteryintothebaseofthe

appliance, as shown on the illustration.

Pushthebatteryuntilitlatchesin.

• Pressthelockingbutton(8)oneitherside

before removing the battery, and disengage

the battery from the base of the appliance.

Onlyusebatteriesofthefollowingtype.Using

any other batteries could cause serious injury or

damage the tool.

• CDA1051: FPB-1800L, 18V Lithium-Ion

• CDA1053: FPB-1800N, 18V NiMH

The following chargers can be used to charge

these batteries.

• CDA1052: FPL-1800 (Lithium-Ion and

NiMH)

• CDA1054: FPL-1800N (NiMH only)

4. OPERATION

Always follow the safety notes and the

relevant safety code.

Make sure that the saw blade does not

rest on or touch any objects when the

machine is switched on.

Switching on and off

Fig. J

• Thismachineisequippedwithasafety

switch (5).

• Startthemachinebypressingthe“lockoff”

button (to disengage the switch) and switch

on the machine.

• Releasethe(On/Off)switch(7)toswitch

the machine off.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm RSM1014 FPRS-1800 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info