Bedienungsanleitung Ferm RSM1014 FPRS-1800 (Seite 6 von 52) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

539202

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

Ferm6

Speed control

Fig. I

• Duringoperationandwhilstthemachine

is at rest the stroke rate (speed) can be

selected using the thumbwheel (6).

• Thestrokeraterequireddependsuponthe

material conditions. The optimal setting

should be determined in use.

• Afterworkingforlongerperiodsatlow

speed you should allow the machine to cool

down by running it at maximum speed with

no-load for approx. 3 minutes.

Sawing tips

• Adjustsawbladeandstrokeratetosuitthe

material to be processed. For right radius

curves it is best to use a narrow saw blade.

Apply coolant or lubricant to deal with the

utteringproducedalongthecutlinewhen

sawing metal.

• Checkwood,chipboards,building

materials etc, for foreign bodies (nails,

screws etc.), before sawing and remove

them, if necessary.

• Clampmaterialwell.Donotsupportthe

workpiece with hand or foot. Do not touch

objectsortheoorwiththesawrunning

(danger of backlash).

• Putthefootplateonthesurfaceofthe

workpiece, and saw through it with constant

contactpressureorfeed.Ifthesawblade

seizes switch the machine off immediately.

Spread the gap with a suitable tool and pull

out the saw blade.

• Afternishingwork,switchoffthemachine

and only put down after it has come to a

complete standstill.

Plunge cutting

Fig. E

• Plungecuttingmayonlybeusedonsoft

materials such as wood, aerated concrete,

gypsum plaster boards, etc.

• However,thisrequiresacertainpractise

and is only possible with short saw blades.

• Placethesawontotheworkpieceand

switch it on.

• Ensurethatthebottomedgeofthefootplate

rests on the workpiece surface as shown.

• Slowlysawintotheworkpieceatanangle,

moving the saw to a vertical position and

continue to saw along the cutting line.

• Switchthesawoffandliftofftheworkpiece

when the work is complete.

Flush sawing

• Elasticbi-metalsawbladesallowyouto

saw protruding objects (e,g, water pipes,

iron bars, etc,) nearby the wall.

• Applythesawbladedirectlytothewall

and bend slightly so that the footplate rests

against the wall.

• Switchthemachineonandsawoffthe

workpiece keeping constant lateral pressure

against the wall.

Rotatable handle

Fig. F

The handle can be rotated in 90° steps to the

machine housing. Slide the rotation button (3)

backwards and rotate the handle to the desired

position. Make sure the handle locks in position

before use.

LCD display

Fig. G

This machine is equipped with a LCD display.

• Toturnthedisplayon,pressthedisplay

button (10) once. To turn the display off,

press the display button again.

• Theclock(11)andminutes(12)remaining

icons indicate the number of minutes of

running time that are available before the

batteryrequiresrecharging(Lithium-Ion

battery only)

• Thebatteryicon(13)indicatesthe

amount of charge remaining in the battery.

Each charge bar displayed indicates

approximately 10% charge remaining in the

battery. A total of 10 charge bars indicates a

fully charged battery.

• Pressthebacklightbutton(14)toswitchthe

backlightofthedisplayon.Pressitagainto

switch the backlight of the display off.

Hex key storage

Fig. H

The included hex key can be stored in the

battery compartment.

5. SERVICE & MAINTENANCE

Make sure that the machine is not live

when carrying out maintenance work

on the motor.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm RSM1014 FPRS-1800 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info