Bedienungsanleitung Ferm SGM1011 (Seite 6 von 144) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

510106

Zoom out

Zoom in

Vorherige Seite

1/144

Nächste Seite

masking tape. The paint or fluid to be sprayed

should be thoroughly mixed and free from lumps

or other particles. Many substances can be

sprayed with your spray gun, but always check

the manufacturers recommendations before

purchasing your paint.

Thinning

Always remember to disconnect from the

mains supply before filling the paint

container with sprayable material.

Most paints are supplied ready for brush

application and will need to be thinned before

they are suitable to be sprayed. Follow the

manufacturers advice on thinning the paint when

used with a spray gun. The viscosity cup will help

you to determine the correct viscosity of paint to

be used. To determine the correct viscosity, fill

the cup to the brim with the paint. Measure the

amount of time it takes for the cup to empty back

into the can.

The table below shows recommended times for

different types of material.

 

Alkyd/Oil based primers from 25 to 40

Alkyd/Oil based farnish from 15 to 40

Acryl/Water based primers from 25 to 40

Acryl/Water based farnish from 20 to 35

Impregnation solvents for wood,

paint removers, oils undiluted

Disinfectant, insectides undiluted

Car paint from 20 to 35

This tool is not suitable for spraying dispersions

and latex paint, caustic solutions, acidic coating

materials, coating materials with granules

or solids as well as spray and drip-impeding

materials.



• Insert the air hose (4) tightly in the connection

on the machine.

• Insert the air hose (4) tightly in the connection

on the spray gun.

Switch on/off

• Push the on/off switch (6) on the machine to

switch the machine off or on.

• Press the trigger on the air gun to start

spraying.

Adjusting the jet settings

Fig. F

A. Horizontal flat jet. This setting is used for

horizontal surfaces

B. Vertical flat jet. This setting is used for vertical

surfaces

C. Circular jet. This setting is used for corners,

edges and hard to reach surfaces.

If the paint takes longer than the recommended

time to empty, then further thinning is required.

Mix in a small quantity of the appropriate thinner

and use the viscosity test until the correct

thickness is achieved. Some sprayable materials

contain particles and lumps. These materials

should be strained before filling the paint

container.



Fig. C

Fill the paint container with the correctly thinned

and strained paint. Connect the spray gun to

the mains supply. Aim the spray gun at a piece

of scrap material and operate the trigger switch

until paint is spraying. Adjust the output control

(2) until the required volume of paint is spraying.

Turn the output control in a clockwise direction

(B) to reduce the flow and anti-clockwise (A) to

increase the flow. Adjustment of the output control

will affect the spray pattern. A poor spray pattern

will concentrate the paint in the centre of the spray

and give a blotchy finish. A good spray pattern

will give even distribution of paint throughout the

pattern.



Fig. D

To obtain the best results, keep your spray gun level

and parallel to the surface at all times. Keep the

nozzle 25 - 30 cm from the surface and spray evenly

from side to side or up and down. Do not spray at an

angle as this will lead to paint runs on the surface.

Use smooth and even strokes. When spraying large

areas, use a criss-cross pattern as shown.

Fig. E

Never start or stop the spray gun while it is aimed

at the surface to be sprayed. Evenly control the

speed of movement of the spray gun. A fast speed

of movement over the surface will give a thin coat

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm SGM1011 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info